Related Manuals for Zenith HealthView H20D50DT
Summary of Contents for Zenith HealthView H20D50DT
- Page 1 Installation and Operating Guide | Warranty Model Number | H20D50DT | HealthView © Copyright 2001, Zenith Electronics Corporation t a b l e o f c o n t e n t s p a g e...
- Page 2 Consult the dealer or an experienced radio/TV technician for help. • CAUTION: Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product. 3-WIRE COMM-WARN B-3/99...
-
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS Important safeguards for you and your new product This product has been manufactured and tested with safety in mind. However, improper use can result in potential electri- cal shock or fire hazards. To avoid defeating the safeguards that have been built into the new product, please read and observe the following safety points when installing and using the new product, and save them for future reference. - Page 4 IMPORTANT SAFETY INSTRUCTIONS (Continued from previous page) 14. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.
-
Page 5: Table Of Contents
User menus, and Source/Channel Bank keys. The installer remote has Menu, Select, and Adjust, and Channel Bank Keys. The LT2000 Quickset II Clone Programmer is used to duplicate a TV’s setup and install it on another identical TV. See your Zenith Dealer. -
Page 6: Antenna
The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire sticking through the middle, and it screws onto the threaded jack on the back of the TV. -
Page 7: Cable Service
DC power. Go to page 11 to Auto Program the TV. If you’re using a cable box, leave the TV on channel 3 or 4 and use the cable box to change channels. If you’re using a cable box, Auto Program might only find the channel the cable service is on (usual- ly channel 3 or 4). -
Page 8: Antenna With Vcr
AA batteries. back of remote Plug in the TV. Do not plug it into a switched outlet. The HealthView TV is designed to oper- ate on standard current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC power. - Page 9 Remove the back of the optional remote and put in two AA batteries. back of remote Plug in the TV. Do not plug it into a switched outlet. The HealthView TV is designed to operate on standard cur- rent, 120-volt 60 Hertz AC. Do not attempt to operate it on DC power.
- Page 10 Controlling the TV with Serial Data The TV is capable of being controlled by a single-wire, serial data signal. This is a Zenith patented technology and is being implemented by certain brands of “smart” pillow speakers, such as Curbell’s “GEN-II” models.
-
Page 11: Auto Program
Shown herein are optional remote controls that can be used by the installer and the patient. Be advise that these remote controls are NOT included with this TV. However, these remotes can be purchased separately, see your Zenith dealer. Mini glossary OFF AIR ANTENNA If the patient can only view over-the-air broadcasts, select Antenna. -
Page 12: Front Panel Controls
HealthView TV. Use the CHANNEL button to cycle through avail- able channels. Use the VOLUME button to adjust the sound level of the HealthView TV. Press CAPTIONS repeatedly to turn selected closed captions option On or Off. (See Captions page.) - Page 13 Turns TV On or Off CC (CLOSED CAPTIONING) Press to access closed captions. Press ENTER to exit. TV/FM Selects TV or Radio on TVs equipped with FM radio. VOLUME LEFT/RIGHT Adjusts the sound levels. ENTER Press to view the Channel/Time display or to remove any on-screen display or menu.
-
Page 14: On-Screen Menus Overview
Allows installer to restrict viewable programming for up to 99 hours, with the use of a password. OTHER MENUS AND ON-SCREEN DISPLAYS Shows the current time, selected channel and XDS* data if available. Sets the time the TV will turn off. Shows current sound level. Sets Caption/Text options. Displays the available channels list. -
Page 15: Setting Add/Delete/Blank
Channel Preview list. Notes: Adding VCR 3 and/or VCR 4 as available channels forces TV Channel 3 and/or 4 to be retained, when run- ning Auto Program, even though the equipment connected to the Antenna/Cable (RF) jack (like a cable converter and/or VCR) may be turned off. - Page 16 Setting Up Channel Labels Overview Channel Labels help the user identify the channel or network being viewed. In the Setup menu with the CH LABELS option highlighted, use the Adjust Left/Right arrows to scroll through the available channel labels, such as, A &...
-
Page 17: Clock Set
1200. For example, to set 6:30 p.m., add 1200 to 630, = enter 1830. For Auto Clock Set to work, the TV must be tuned to a local PBS station. If the TV does not set the time, set the clock time manually. -
Page 18: Captions
Availability and functionality of Caption/Text options are determined only by each broadcaster and may not be available in your area. Mini glossary CAPTIONS The term for the words that scroll across the bottom of your TV screen; usually the audio portion of the program provided for the hearing impaired. TEXT The term for the words that appear in a large black frame and almost cover the entire screen;... -
Page 19: Language
Use the SELECT key on the remote control, to highlight Language on the screen. Press the Right/Left ADJ arrow to choose one of the following options: English, Spanish or French. Press ENTER to return to TV viewing. 206-3491-O ENGLISH POWER... -
Page 20: Video Menu
Contrast on the screen. Using the Right/Left ADJ arrow, change the contrast level to your preference. Press ENTER, or MENU one more time to return to TV view- ing, or repeat from step two to set the other menu options. Picture Preference Use SELECT to choose Picture Preference on the screen. -
Page 21: Fm Radio Menu
FM Radio Menu Use the FM Menu to customize FM Radio options Press TV/FM and choose the FM Radio operating mode, on the optional Installer’s remote. Press the MENU key repeatedly until the FM Setup Menu appears. Your options are: •... -
Page 22: Installer Parental Control Menu
Overview To insure complete coverage for all TV programs, (movies and regular TV shows) choose a rating for MPAA, from the selec- tions below AND choose ratings from the TV Parental Guidelines Rating System on the next page, using the Age Block option for General Audiences, and for Children. -
Page 23: Installer Parental Control Menu
Installer Parental Control Menu After you have read the preceding page, follow instructions below to set up and activate Parental Control Note: Use the installer’s remote control to specify Parental Control settings. Press MENU repeatedly until the Parental Control Menu appears using the optional Installer’s remote. -
Page 24: Other Menus And On-Screen Displays
Parental Control menu. INACTIVE TV PLEASE . . . CALL ATTENDANT Inactive TV Display Prompts patient to arrange for TV service to room. Sleep Timer Menu Press TIMER. Sets TV shut-off time and shows remaining time before TV shutoff. -
Page 25: Managing The Channel Banks
Managing the Channel Banks Using the optional Installer’s remote control, the TV has four channel banks, where the administrator or installer can store groups of TV channels PLANNING THE CHANNEL BANKS Generally, TV channels are grouped into “program pack- ages” with terms that are proposed to the end user. The user then opts for a package. - Page 26 Managing the Channel Banks Examples of typical channel banks charts Figure 1. Typical channel banks after running Auto Program B Purpose A = Active - - Channel was found during AUTO PROGRAM Figure 2. Typical channel banks after running Auto Program, and customizing with Add/Del/Blnk B Purpose 1 Basic BC A...
- Page 27 Managing the Channel Banks PLAN YOUR CHANNEL BANKS BY FILLING IN THESE CHARTS (or use photocopies) B Purpose B Purpose 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 B Purpose 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 B Purpose...
-
Page 28: Installer Menus
Installer Menus Use the Installer’s Menus to make TV operation adjustments Accessing the Installer’s Menu Installer’s menus can be accessed by using the optional installer’s remote control. Just press and hold MENU (about 8 seconds) until the display changes, then press 9, 8, 7, 6, then ENTER. To exit the Installer’s Menu, press ENTER again. - Page 29 The range is 0 to 63, with 63 as the default which gives the patient the full range of volume control. Change values with ADJUST keys. It may be best to set the same value on every TV. NOTE: The maximum volume level cannot have a value setting lower than the MIN VOLUME level (described above).
- Page 30 24 FEATURE LEVEL (Note: Leave set to 1 otherwise the TV can- not be operated unless a Zenith private label remote is used.) Set to 1 for default Zenith IR Code recognition. Set to 0 for Zenith Private Label IR Code recognition.
-
Page 31: Lt2000 Quickset Ii Clone Programmer
TV into multiple identical television sets. Once learned from the master, setup data is retained in the LT2000 for future use. When using the LT2000, cloning operations will go easier if the TV set is connected to a good quality signal and operating with a stable picture displayed. -
Page 32: Clone Selection Menu Choices
Since the Clone Programmer’s time cannot be set directly, the time needs to be copied from a Zenith TV equipped with MPI input capability. Once the time is copied to the Clone programmer, the current time can then be transferred to another TV. -
Page 33: Operation Notes
• TV not reset. When cloning operations are complete, just unplug the LT2000 from the TV. If the TV does not display a picture (blank screen) after a few seconds, just change channels. 206-3491-O The LT2000 programmer is designed to be used with TVs contain- ing the 221-01006 and later processors. - Page 34 Patient Remote Key Functions A quick list of the keys on the optional patient remote and what they do in TV mode POWER Turns TV On or Off CC (CLOSED CAPTIONING) Press to access closed captions. Press ENTER to exit.
- Page 35 A quick list of the keys on the optional patient remote and what they do in FM Radio mode POWER Turns TV On or Off TV/FM Press for TV or FM radio mode. VOLUME (UP/DOWN) Adjusts the sound levels. TIMER Press and repeat to set the time the TV will turn itself off.
- Page 36 NC-17 Restricted Viewing Hard Core Films Note: Zenith Electronics Corporation is not liable for any program content that appears when using this rating system; as always, user discretion is advised. P A G E 3 6 You cannot disable Parental Control by disconnecting the TV from power.
-
Page 37: Parental Control Menu
Press ADJ Right arrow to go to the CONTENT BLOCK menu. Use SELECT to highlight an option like SEX SCENES. Press ADJ Right arrow to choose: Unblocked, TV-PG AND ABOVE, TV-14 AND ABOVE, or TV-MA. (AND ABOVE means more restrictive headings are automatically included when you choose a low restriction setting like TV-PG.) See the Mini Glossary, Ratings... -
Page 38: Patient Parental Control Menu
TV. CAPTION 1 IS ON Closed Captions Menu Press CC. Turns selected closed captions/text option on or off. Sleep Timer Menu Press TIMER. Sets TV shut-off time and shows remaining time before TV shut-off. Rating: Ch 25 - PBS 7:15... -
Page 39: Maintenance
Extended Absence If the TV is to be left dormant for a long time, it’s a good idea to unplug the power cord to protect against possi- ble damage from lightning or power surges. If you use an off-air antenna, you may also want to disconnect it from the back of the TV. -
Page 40: Troubleshooting
• Check the antenna connection or location. • Check the cable input. • Check to see if the TV/ VCR button on the VCR has the TV selected. • Check the antenna direction and/or location. • Check the cable input. -
Page 41: Glossary
The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire sticking through the middle. It screws onto the threaded jack on the back of the TV. 300 TO 75 OHM... -
Page 42: Notes
Notes P A G E 4 2 206-3491-O... - Page 43 Notes P A G E 4 3 206-3584-0...
- Page 44 Direct-View Color TV Welcome to the Zenith family! We believe that you will be pleased with your new TV. Please read this warranty carefully, it is a “LIMITED WARRANTY” as defined under Federal Law. This warranty gives you specific legal rights, and you may also have other rights that vary from state-to-state within the U.S.A.