Consult the dealer or an experienced radio/TV technician for help. • CAUTION: Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product. HealthView...
IMPORTANT SAFETY INSTRUCTIONS Important safeguards for you and your new product Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.
Page 4
IMPORTANT SAFETY INSTRUCTIONS (Continued from previous page) 14. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.
Source/Channel Bank keys. The installer remote has Menu, Select, and Adjust Keys (Up/Down/Left/Right arrows) and Source/Channel Bank Keys. The LT1500 Clone Programmer is used to duplicate a TV’s setup and install it on another TV. See your Zenith Dealer.
The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire sticking through the middle, and it screws onto the threaded jack on the back of the TV.
Remove the back of the remote and put in two AA batteries. back of remote Plug in the TV. Do not plug it into a switched outlet. Your HealthView TV is designed to operate on household current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC Current.
120-volt 60 Hertz AC. Do not attempt to operate it on DC Current. Go to page 11 to Auto Program the HealthView No A/V cables are included with the Zenith HealthView P A G E 8 Antenna Flat wire...
Remove the back of the remote and put in two AA batteries. back of remote Plug in the TV. Do not plug it into a switched outlet. The HealthView TV is designed to oper- ate on standard current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC Current.
(when measured from pin 4) with the switches open. Current draw is 8 mA when a switch is closed. (This operation is identical to previous Zenith models using the 5-Wire Interface except that only +7 volts DC was supplied and current draw was only 2.5 mA.) Pin no.
Press a Right or Left ADJ arrow to begin the Channel Search. Press ENTER when finished. Note: Auto Program finds channels being received by the TV tuner. Cable will not work unless the hospital provides a cable service. (If the Auto Program line appears in red, then it did not pass one of the internal tests.
Front Panel Controls Using the front control panel to access the menus. Press the POWER button to turn on the HealthView Press the CHANNEL button, cycle through available channels. Press the VOLUME button to adjust the volume of the HealthView Press CAPTIONS to select captions 1-4, text 1-4 or captions off.
Displays the available TV channels and hotel patient’s Parental Control menu. Allows user to select the Aux Channel. (Use the Audio/Video jacks on the back of the TV as the source of the picture and sound.) P A G E 1 3...
Channel Labels Labels the channels with their network names (ABC, CBS, HBO, etc.). Timer Setup Programs a time for the TV to turn itself on or off, or to turn itself off after a certain amount of time. Clock Set Sets the time.
Channel Preview list. Notes: Adding VCR 3 and/or VCR 4 as available channels forces TV Channel 3 and/or 4 to be retained, when run- ning Auto Program, even though the equipment connect- ed to the Antenna/Cable (RF) jack (like a cable convert- er and/or VCR) may be turned off.
Setting Up Channel Labels Overview Channel Labels help the user identify the channel or network being viewed. In the Setup menu with the CH LABELS option highlighted, use the Adjust Left/Right arrows to scroll through the available channel labels, such as, A & E, AMC, ESPN, HBO, etc.
Timer Set Up Set times to turn the HealthView TV on or off automatically. Be sure to set the Clock first, see next page. With Timer Setup highlighted as shown above, press a Left/Right ADJ arrow to display the Timer setup menu.
6:30 on the clock. Use the TIMER key to specify AM or PM. Press ENTER to start the clock and return to TV viewing. The Sleep Timer may be instantly set by pressing the TIMER key repeatedly. When you have made the selection, press ENTER to set the timer and return to TV viewing.
Mini glossary CAPTIONS The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing impaired.
Use the SELECT key on the remote control, to highlight Language on the screen. Press a Right/Left ADJ arrow to choose one of the fol- lowing options: English, Spanish or French. Press ENTER to return to TV viewing. P A G E 2 0 ENGLISH POWER...
Using a Right/Left ADJ arrow, change the contrast level to your preference. Press ENTER, or MENU one more time to return to TV view- ing, or repeat from step two to set the other menu options. Use SELECT to choose Picture Preference on the screen.
Radio to remain on to four hours. Press ENTER to clear the screen. NOTE: The Sleep Timer will be turned off if you turn the TV off. • Clock Set: Set the clock in this menu with the numbers.
Overview To insure complete coverage for all TV programs, (movies and regular TV shows) choose a rating for MPAA, from the selec- tions below AND choose ratings from the TV Parental Guidelines Rating System on the next page, using the Age Block option for General Audiences, and for Children.
Page 24
After you have selected and adjusted the parental control menu options to your preferences: - Set the number of hours Advanced TV Control will be on. - Set a 4-number password. - Set the Lock On/Off option to either on or off.
NUMBER keypad and TIMER. CAPTIONS Closed Captions Menu Sets closed captions options and shows currently selected option. Sleep Timer Menu Press TIMER. Sets TV shut-off time and shows remaining time before TV shutoff. CHANNEL PREVIEW - - - - - - - -...
Managing the Channel Banks The TV has four channel banks, where the administrator or installer can store groups of TV channels. PLANNING THE CHANNEL BANKS Generally, TV channels are grouped into “program pack- ages” with terms that are proposed to the end user. The user then opts for a package.
Page 27
Managing the Channel Banks Examples of typical channel banks charts. Figure 1. Typical channel banks after running Auto Program B Purpose A = Active - - Channel was found during AUTO PROGRAM Figure 2. Typical channel banks after running Auto Program, and customizing with Add/Del/Blnk B Purpose 1 Basic BC A...
Page 28
Managing the Channel Banks PLAN YOUR CHANNEL BANKS BY FILLING IN THESE CHARTS (or use photocopies). B Purpose B Purpose 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 B Purpose 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 B Purpose...
Installer Menus Use the Installer Menus to make adjustments. Accessing the Installer Menu Installer menus can be accessed by using the installer’s remote control. Just press and hold MENU (about 8 seconds) until the display changes, then press 9, 8, 7, 6, then ENTER. To exit the Installer Menu, press ENTER again.
The range is 0 to 63, with 63 as the default which gives the patient the full range of volume control. Change values with ADJUST keys. It may be best to set the same value on every TV. NOTE: The maximum volume level cannot have a value setting lower than the MIN VOLUME level (described above).
Page 31
Generally, this feature is used in connection with START CHAN/VOL (line 11) where the start channel may, for example, be set to 3 or 4. If the start channel is 3 then the TV will remain on channel 3. NOTE: When channel lock is active AUTO PROGRAM and CH.
If you have previously stored a TV setup in a particular clone memory, it may be changed if desired by overwriting it with a new setup. There is no need for a separate memory clear operation.
Item 4: Set TV Clock From Clone To set the real time clock in the TV, press (4), then press ON/OFF, POWER, or ENTER to copy the current clone time to the TV clock. Alternatively, use the TV front panel CHANNEL UP or CHANNEL DOWN keys to highlight your choice, then press ON/OFF, POWER, or ENTER to activate.
Alternatively, use the TV front panel CHANNEL UP or CHANNEL DOWN keys to highlight your choice, then press ON/OFF, POWER, or ENTER to begin. The TV screen will display the items in the installer menu setups for you to observe. Use this function to quickly check the contents of a particular clone memory for the correct setup.
Parental Control menu. Allows patient to select the Video Channel. (Use the Audio/Video jacks on the back of the TV as the source of the pic- ture and sound.) P A G E 3 5...
Page 36
Patient Remote Key Functions-FM Radio A quick list of the keys on the patient remote and what they do. POWER Turns TV On or Off TV/FM Press for TV or FM radio. VOLUME (UP/DOWN) Adjusts the sound levels. TIMER Press and repeat to use the Sleep Timer.
NC-17 Restricted Viewing Hard Core Films Note: Zenith Electronics Corporation is not liable for any program content that appears when using this rating system; as always, user discretion is advised. 206-3491-O Even if you choose to leave the Aux inputs unblocked, the ratings you specify will automatically restrict the program- ming that appears from the video sources.
After you have selected and adjusted the parental control menu options to your preferences: - Set the number of hours Advanced TV Control will be on. - Set a 4-number password. - Set the Lock On/Off option to either on or off.
CAPTIONS Closed Captions Selected Press CC. Sets closed captions and shows Caption/Text options. Sleep Timer Menu Press TIMER. Sets TV shut-off time and shows remaining time before TV shut-off. CHANNEL PREVIEW - - - - - - - -...
Maintenance Routine TV cabinet and screen cleaning. Careful and regular cleaning can extend the the useful service life of the TV. Be sure to turn the power off and pull out the plug before you begin any cleaning. Screen Cleaning 1.
SOLUTIONS • Check the antenna connection or location. • Check the cable input. • Check to see if the TV/.VCR button on the VCR has the TV selected. • Check the antenna direction and/or location. • Check the cable input.
The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire sticking through the middle. It screws onto the threaded jack on the back of the TV. 300 TO 75 OHM...
Read your Operating Guide carefully so that you will understand the operation of the TV and how to adjust the controls. Carry-In Service Models under 21” diagonal (U.S.A.) screen size must be taken to a Zenith authorized service center for warranty service and must be picked up by the owner.