Table of Contents
Advertisement
Available languages
Available languages
CONTROLS
FRONT PANEL
10.
11,
12,
1
2
3
4
5)
(6)
VW
|
I
'oo
|
[=
| tee.
(Oo
[=
sen
ES
9
10
11
13)
(14)
(5
12
POWER Switch
Depress to turn on the power and depress again to turn off the power.
Depress only the upper part of the switch (near the word POWER).
*
Due to the incorporation of a protection circuit, no signal will
be out-
put to the speakers for few seconds after the power is turned on.
SPEAKERS Switches with Indicators
A: Turn
on the switch to listen through
speakers connected
to the rear
panel
A SPEAKER
terminals.
B: Turn
on
the switch to listen through
speakers connected
to the rear
panel
B SPEAKER
terminals.
Turn on both switches to listen through two sets of speakers connected
to both A and B SPEAKER
terminals.
*
A and B SPEAKER
terminals accommodate
speakers of 4 to 16 ohm
impedance,
but if both
A and
B SPEAKER
terminals are used simul!-
taneously, speakers of 8 to 16 ohm impedance must be used.
VOLUME
Control
For volume
adjustment.
Slide the control
to the right to increase the
volume,
MUTING Button
afterwards to regain the previous votume level.
Recording (REC) Indicators
Interconnected with the REC SELECTOR.
LOUDNESS Button
When listening at a low volume level, the range audible by the human ear
is limited. The loudness circuit supplements this range by boosting the
bass and treble response. Depress the button for balanced sound at low
volume,
Input Switches with Indicators
PHONO:
Turn on the switch
to monitor
a record being played back on
a turntable connected to the rear panel PHONO jacks.
Turn on the switch
to monitor
a radio broadcast from a tuner
connected to the rear panel TUNER
jacks.
TUNER:
TAPE-1:
Turn
on the switch
to monitor
a tape being played back on a
tape deck connected to the rear panel TAPE-1 jacks.
TAPE-2:
Turn on the switch
to monitor
a tape being played back on a
tape deck connected to the rear pane! TAPE-2 jacks.
AUX:
Turn on the switch to monitor an equipment connected to the
rear panel AUX
jacks.
Also
use
these
switches
to monitor
the desired
input source
during
recording.
Headphone Jack (PHONES)
:
Accommodates
8 ohm
low impedance
type stereo headphones for moni-
toring or private headphone listening.
LINE STRAIGHT Switch with Indicator
When this switch
is turned on, the signals will bypass the tone controls
and the MODE
selector. Therefore, the signals will be output in stereo with
no tone control effect regardless of the setting of the Tone controls and
the MODE selector.
Tone Controls
*
Set
to
DEFEAT
for
flat frequency
response
with
no
tone control
effect.
BASS:
*
For low range frequency
response control. Can be adjusted
from —8 dB to +8 dB.
MODE Selector
STEREO
(ML):
For stereo playback.
from both the left and right speakers.
SUBSONIC Switch
Turn ON
(-m) the switch
to eliminate low frequency
disturbances such
as turntable rumble, etc.
REAR PANEL
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
sweet cagiag ap at at
Wadi ACER ECE Un
WevRsAESRCUAAE LU
AKAHILEC AR COU
(Cason no AME
Stereo BALANCE Control (L: left, R: right)
For left and right speaker balance. Turning clockwise reduces thi
of the left channel and turning counterclockwise reduces the vc
the right channel. Output of fteft and right channels is equal wh
the center click position.
PHONO Selector
Set according to the type of cartridge used.
MC:
When using a moving coil type cartridge.
33:
When using
a moving magnet type cartridge with 33 kc
impedance.
47:
When
using a moving magnet type cartridge with 47 kc
impedance.
100:
When using a moving magnet type cartridge with 100 kc
impedance.
*
Turn down the volume before setting the selector.
Recording (REC) SELECTOR
Use this selector to select the desired signals to be recorded by
deck(s).
This selector
lets you
record
one
source
while
play
another source selected by the Input switch.
DUBBING
2
1: Set to this position
when
dubbing
from
at
connected
to the rear panel TAPE 2 jacks 1
deck connected to the rear panel TAPE 1 jack
Set to this position when
dubbing from a t
connected
to the rear panel TAPE
1 jacks 1
deck connected to the rear panel TAPE 2 jack
DUBBING
1
2:
OFF:
Set to this position when
not recording.
PHONO:
Set to this position
when
recording from
a'
connected to the rear panel PHONO jacks.
TUNER:
Set to this position when recording a radio t
from
a tuner connected
to the rear panel
jacks,
AUX:
Set to this position when recording from an ec
connected to the rear panel AUX
jacks.
PHONO
Jacks
Connect the output cable of magnetic type cartridge turntable,
*
Use AUX
jacks for connection
of crystal
or ceramic
type
turntable,
Ground Terminal (7+7)
Connect to the Ground terminal of turntables, tape decks, etc.
*
When
connecting
a turntable connect
the ground wire to thi:
terminal.
TAPE 1 REC/PLAY Jacks
For connection to a tape deck for recording/playback.
REC:
Connect to the input (LINE IN) jacks of tape deck for ri
PLAY:
Connect
to the output
(LINE
OUT)
jacks of tape deck
back,
A and B SPEAKER System Terminals
Be sure to match plus and minus and left and right. If plus ar
terminals are reversed, poor and unnatural
sound will result.
TUNER Jacks
Connect to the output (OUTPUT) jacks of tuner.
AUX Jacks
For connection of relatively high output equipment such as ac
ceramic type cartridge turntable or a tape deck or recorder.
TAPE 2 REC/PLAY Jacks
AC OUTLETS
(Some models are not equipped with this facility.
UNSWITCHED
Outlet:
Not
interconnected
with the front per
ER
switch.
Power
is supplied even v
AM-U61 is turned off, 200W MAX.
Interconnected
with
the front panel
switch. Power iscut when the AM-U61
off. TOTAL 100W MAX.
SWITCHED Outlets:
Power Cord
Advertisement
Table of Contents
