Panasonic SC-AK630 Operating Instructions Manual page 10

,
..... i i
iiiiiiiiiiiii!i!iiiiiiiiiiii!!!i!i!ii!!i i ÷/REw/v,
_,TAPE
_/|L CD
CLOCK/TIMER
Numbered
buttons
Automatic presetting
Do the following once each for FM and AM.
Preparation: Tune to the frequency where pre-setting is to begin.
Hold down [PROGRAM] until the frequency changes.
The tuner presets all the stations it can receive into the channels in
ascending order. When finished, the last station memorized is tuned in.
Manuam presetting
Pre-set the stations one at a time.
_1" Press [PROGRAM] then press [_, PEW/V] or
[_, A/FF] to tune to the desired station,
f2_ Press [PROGRAM] then press [_.,_, PEW/V] or
[l_{bq, A/FFj to select a channel
t3; Press [PROGRAM].
The station occupying a channel is erased if another station is preset
in that channel.
Selecting channels
Press the numbered buttons to select the channel.
To enter a 2-digit channel, press [=>10], t hen the two digits.
RQT7834
Press [TUNER, BAND] to select band.
The unit comes on.
Every time you press the button:
FM _ AM
Press[PLAY MODE] on the remote contromto eemect
"MANUAL"°
Everytimeyoupressthebutton:
MANUAL_PRESET
Ho_d down [_/REW/V] or [Ib,C_/FF/A] for a moment
to search for a station,
The frequency stops when it finds a clear station.
To stop during the process, press [I_/REW/V] or [_H/FF//k].
Under excessive interference, a station may not be found.
Press [F_.,_/REW/V] or [_/FF/A] repeatedly to tune step-by-
step.
"TUNED" is displayed when a radio station is tuned.
"ST" is displayed when a stereo FM broadcast is being received.
tf noise is excessive in FM
Remote control only
Hold down ]PLAY MODE] to diep{ay "MONO'L
Monaural sound is selected and noise reduces when reception is
weak.
Hold down [PLAY MODE] again to cancel the mode.
"MONO" is also cancelled if the frequency is changed.
To receive FM broadcasts allocated in 0.1 MHz
Main unit only
Hold down [TUNER, BAND]. The display changes in a few seconds to
show the current minimum FM frequency. Continue to hold down the
button until the minimum frequency changes. The step is changed.
Repeat the above to change the step back.
o After changing the "allocation" setting, the frequencies you previously
preset in the memory will be cleared.
o Sound is momentarily interrupted if you load/unload tapes while
listening to an AM broadcast.
Remote controt only
There are two methods of pre-setting stations.
Automatic presetting : All the stations the tuner can receive are preset.
Manua_ presetting : You can select the stations to preset and the
order they are preset in.
Up to 15 stations each can be set in the FM and AM bands.
Preparation:
Press [TUNER, BAND] to select "FM" or "AM".
OR
Press [PLAY MODE] to select "PRESET".
_2_ Press [1_, REW/V] or [_l_q, A/FF] to select the
channel
Use outdoor antenna if radio reception is poor.
FM outdoor
antenna
Rear
panel
of this
unit
-- FM outdoor antenna
(not included)
-- 75 _,! coaxial cable (not included)
30ram
(1 3116 )
Shield braid
15ram
[C._ ) Core wire
,, Disconnect the FM indoor antenna.
,, The antenna should be installed by a competent technician.
AM outdoor antenna
AM outdoor antenna (not included)
Rear _ AM loop
panel antenna
of this (included)
unit
Run a piece of vinyl wire horizontally across a window or other
convenient location.
Leave the loop antenna connected.
Disconnect the outdoor antenna when the unit is not in use.
Do not use the outdoor antenna during an electrical storm.