Table of Contents
Advertisement
36
38
Installation
Preparation
* Before installation check the radio operation with antenna and speakers.
Disconnect the cable from the negative (—) battery terminal {see caution below).
Caution:
For installation to cars with trip or navigational computers, all electronic memory settings previously registered
In-dash Installation
Installation Opening
In-dash installation can be done if the car's dash-
board has an opening for this unit as shown in Fig.
1, The car's dashboard should have a thickness of
4.5mm - 6mm in order to make the installation of
the unit.
53 mm
fe —t82 mm:
Fig. 1
Installation Precautions
This equipment, if possible, should be installed by a professional installer.
In case of difficulty, please consult your nearest authorized Panasonic Service Center.
3. Connect the power lead atter other connections are made.
5. Insulate all exposed wires to prevent short circuitting.
6, Secure all loose wires atter installing the unit.
Supplied Hardwares
@_ | Mounting Collar
Remote Control Unit
Mounting Bolt (5 mma)
® | Trim Plate
Power Connector
Removable Face Plate
Case
Lithium Battery
@®) | ISO Antena Adaptor
3. a) Plug the Power Connector ©.
b) Install the Trim plate ©.
a ® Power Connector
© Trim Plate
4. After installation reconnect the nega-
tive (—) battery terminal.
To Remove the Unit
a) Remove the removable face plate. (See page 33.)
b) Remove the trim plate with a screwdriver as shown in the figure.
Trim Plate
Screwdriver
b) Pull out the unit while pushing the lock lever using Screwdriver. (Fig. 1, Fig. 2)
¢) Remove the unit pulling with both hands. (Fig. 3)
Lock Lever
-12-
instal | ati 0 n continued
Installation Procedures
1. Secure the Mounting Collar ®.
Dashboard ~
@ Mounting Collar
2. Secure the rear of the unit.
Screwdriver
Mounting Tab
Lock Lever
Make sure that the
lock lever is flush
with the mounting
collar (not projecting
outward).
@ Mounting Bolt ae ~5p
d) Secure the rear of the unit to the car by either of
@ Using the Rear Support Strap (Optio
Unit
the two recommended methods.
nal)
Car, or some other metallic area.
lf Using the Rubber Cushion (Optional)
{If there is an existing Rear Support Bracket on the Fire Wall of Car.)
Cover Mounting Bolt @ on the rear of the unit with Rubber Cushion, and mount it into
the existing
Rear Support Bracket.
Fire Wall of Car
Tapping Screw (Optional)
4
3mmeo
oe
a
Hex Nut (Optional)
3,
Rear
Support St
Optional
NP
(2) Mounting Cotlar
Rear Support Bracket
{existing on the car)
\
Rubber Cushion (Optional) \
37
Fuse (3.154)
(Yellow)
Battery Cord
To a Constant power supply
D Changer
(Wnito) (Whitey Centro! Connector
© This unit can be connected to an
optional CD changer (CX-DP801/
803EN, CX-DP600EN/AEN,
CX-
DP601EN or CX-DP1200EN).
For details consult your nearest
authorized Panasonic Dealer.
© For connection to a CD changer,
refer to the operating instructions
of the CD changer (CX-DP801/
803EN, CX-DP600EN/AEN,
CX-
OP6O1EN or CX-DP1200EN).
<Back Skte>
PREAMP OUT CONNECTOR
(Front)
'
@ISO Ant
ANTENNA
iw!
CQ-DFX555/DFX35SLEN
Dark Btue
(AS)
PREAMP OUT CONNECTOR(Rear)
Orange
cy
>
aT
®
Black
ae
SPEAKER LEAD|
Gray w/Biack Stipe
—~~~|
White w/Btack
Violet w/Btack Stripe
67
Supe \(Famte \( rey
Groen wilack))| Green)
Violet
® Brown _/ ;— 88
tr
=
a
Be
Nw
IL
be
3
aa
Qa
B2
Loudspeakers (connector B)
—s1
Left +
Left —
Right +
Right -
e
B6 (White w/Black
B4 (Gray w/Black
Front
BS (White)
eis)
B3 (Gray)
Site)
Rear
87 (Green)
| 88 ie
aa
Bi (Violet)
Re Went aBlack
A4
A8
BATTERY LEAD (To Battery of Car) (Yellow)
'GROUND LEAD (Black)
Connect to the "BAT" terminal on the fuse block of the car.
Connect to a well grounded metallic part of your car,
The power should be supplied continuously to the yellow
\ leads regardless of the on/off position of the ignition key.
)
a
AS
TELEPHONE MUTE LEAD (Orange)
(eres one Pe
ere a
This lead is not in
for use with switch actuated power
The telephone mute
lead, if connected to the car telephone
antenna.
AMP-RELAY CONTROL POWER LEAD
This lead is for connection to Panasonic power amplifier.
AZ
mute line, wil activate the muting circuit and the sound from
the speakers cannot be heard while the telephone conver-
sation is in progress.
Noto: This telephone mute lead is for connection anly to the
radio mute line. Be sure to ascertain this because it will not
work with other type of output system.
Connect to the "radio" power tine of the car or to the "IGN"
'or "ACC" terminal of the fuse block.
,;
ee LEAD (Red)
39
CQ-DFX555/355LEN
Advertisement
Table of Contents
