Page 1
User Manual of Product 1: Garmin Varia™ RCT715, Bicycle Radar with Camera and Tail Light, Continuous Recording, Vehicle Detection User Manual of Product 2: Garmin Varia UT 800 Smart Headlight Urban Edition with Dual Out-front Mount...
Installing the Tail Light Mount....3 Device Information......15 Device Overview........4 Charging the Device......15 Varia RCT715 Device Status LED... 5 Tips for Charging the Device.... 15 Varia RCT715 Camera Status LED..5 Connecting the Device to Your Tail Light Modes and Intensity....5 Computer..........
13). Tips for Installing the Device The Varia RCT715 device includes a tail light and micro radar that can detect approaching vehicles up to 140 meters away. • Select a secure location to mount the device where it does not interfere with the safe operation of your bike.
Page 7
• Install the device correctly. The device faces backward and is perpendicular to the road. • Make sure there are no obstructions in front of the light. • Go for a test ride during the day in a safe environment. Introduction...
Installing the Tail Light Mount 1 Select a rubber pad based on your seat post shape, and place the rubber pad on the back of the tail light mount. 2 Place the tail light mount on the seat post. 3 Attach the tail light mount securely using one band 4 Align the tabs on the back of the device with the tail light mount notches 5 Press the locking lever down until it locks into place.
Hold for 2 seconds to turn the device off. Changes color based on the battery level, pairing status, device modes, and charging status (Varia RCT715 Device Status LED, page Device status LED Changes color based on the camera status (Varia RCT715 Camera Status LED, page Camera status LED Hold for 1 second to save a video or take a picture.
Flashing blue The device is in Wi‑Fi ® sharing mode. Tail Light Modes and Intensity You can switch the Varia RCT715 tail light modes by pressing the device button (Device Overview, page Flash Behavior when Mode Light Intensity Default Flash Behavior...
The Varia RCT715 and the Varia App The Varia app connects to your Varia RCT715 device using Bluetooth technology. The app displays radar ® information, settings, videos, and photos. Select to take a photo. Displays radar information (Viewing Radar on the Varia App, page Displays a colored banner indicating the threat level posed by approaching vehicles.
Pairing the Varia Radar Device with Your Phone The first time you connect the Varia RCT715 device to the Varia app on your phone, you must pair both devices. After the initial pairing, the Varia app automatically connects to the Varia RCT715 when you open the app and the radar device is active and within range.
It is your responsibility to know and follow all laws, regulations, and any other restrictions in jurisdictions where you plan to use this device. The Varia RCT715 records video to the memory card (Replacing the Memory Card, page 17).
(Device Overview, page • Select on the Varia app (The Varia RCT715 and the Varia App, page NOTE: This option is available only during Continuous mode (Changing Your Recording Mode, page • Select Take a Photo or Save a Clip on your compatible Edge device.
Pairing the Varia Radar Device with Your Edge 1030 The first time you connect the Varia RCT715 device to your Edge device, you must pair both devices. After the initial pairing, the Edge device automatically connects to the radar device when you start your activity and the radar device is active and within range.
The alert tone for approaching vehicles has a unique sound. The device beeps one time when the first vehicle is detected. After the threat is cleared, the device beeps again when another vehicle is detected. The Varia RCT715 and Your Edge 1030 Series...
13). Testing the Light Network 1 From the Sensors menu, select Lights > Network Options > Test Lights. 2 Select a light to test. The light blinks when it is connected. The Varia RCT715 and Your Edge 1030 Series...
3 From the Sensors menu, select Add Sensor > Search All. 4 While the Varia RCT715 device is turned off, hold the device button for 2 seconds to enter pairing mode. The status LED flashes purple, and the tail light turns on. The device is in pairing mode for 5 minutes or until you press the device button.
3 From the Settings menu, select Sensors > Add New > Search All. 4 While the Varia RCT715 device is turned off, hold the device button for 2 seconds to enter pairing mode. The status LED flashes purple, and the tail light turns on. The device is in pairing mode for 5 minutes or until you press the device button.
• Connect the charger securely to the device. You can charge the device by plugging the USB cable in to a Garmin approved AC adapter with a standard wall outlet or a USB port on your computer. Charging a fully depleted battery takes about 5 hours using a computer and 3 hours using an AC power source.
Connecting the Device to Your Computer You can connect the device to your computer to install software updates or transfer videos and photos to your computer. 1 Pull up the weather cap from the USB port 2 Plug the small end of the USB cable into the USB port on the device. 3 Plug the large end of the USB cable into a USB port on your computer.
Replacing the Memory Card You can replace the memory card to increase the storage capacity or to replace a card that has reached the end of its useful life. The device requires an 8 to 128 GB microSD memory card with a speed rating of Class 10 or ®...
5 Close and latch the card holder 6 Close and latch the cover. Device Care NOTICE Do not store the device where prolonged exposure to extreme temperatures can occur, because it can cause permanent damage. Avoid chemical cleaners, solvents, sunscreen, and insect repellents that can damage plastic components and finishes.
Hold both buttons for 10 seconds until both LEDs turn off. Resetting deletes the pairing connections from the device. The device withstands incidental exposure to water of up to 1 m for up to 30 min. For more information, go to www.garmin.com/waterrating. Troubleshooting...
Radar detection does not work indoors The Varia RCT715 device is tuned to detect vehicles in an outdoor setting. If you turn on the device indoors, a saturation alert can occur. When you take the device outdoors, the device resumes normal operation.
The radar device disconnects from the Edge device WARNING If the radar device is not connected or sending radar data, Garmin recommends that you stop riding and check the devices in a safe location. Failure to do so could result in serious injury or death.
Replacement parts are available for this device. Contact your Garmin dealer or go to garmin.com for more information. Getting More Information • Go to support.garmin.com for additional manuals, articles, and software updates. • Go to buy.garmin.com, or contact your Garmin dealer for information about optional accessories and replacement parts. Troubleshooting...
Page 29
May 2022 GUID-FF49DAFA-3213-4C92-924F-2532424071B1 v1...
Page 32
Table of Contents Introduction........1 Installing the Out-Front Mount....2 Installing the Helmet Mount....5 Device Overview........6 Turning On the Device......6 Bike Light Status LEDs......6 Device Settings........ 6 Pairing Your Bike Light with Your Edge 830 or 1030..........7 Customizing Headlight Settings with Your Edge Device........
Introduction WARNING See the Important Safety and Product Information guide in the product box for product warnings and other important information. The device is intended for outdoor use. Without proper airflow during use, the device may become hot. Handle with care. Introduction...
You can use the out-front mount to install the headlight and your Edge ® device. Garmin recommends that you adjust the mount for the Edge viewing angle before you install and adjust the headlight angle. 1 Select a secure location to mount the Edge device and headlight where they do not interfere with the safe operation of your bike.
Page 36
9 Insert the screw , and hand tighten. 10 Align the notches of the quarter-turn adapter with the tabs on the bottom of the mount. 11 Press up slightly, and turn the adapter counterclockwise until it locks into place. 12 Adjust the headlight angle so it is parallel to the ground, and use the 4 mm hex key to tighten the screw. Introduction...
Page 37
NOTE: You should check the tightness of the screw periodically. Introduction...
Installing the Helmet Mount 1 Select a secure location to mount the headlight where it does not interfere with the safety and comfort of your helmet. 2 Attach the mount using both straps. 3 Lock the straps by pressing down the clasp. 4 Connect the adapter to the headlight.
The lever must be flush with the base. 9 Adjust the headlight angle, and use the 4 mm hex key to tighten the screw. NOTE: You should check the tightness of the screw periodically. Device Overview Hold for 1 sec. to turn the device on. Hold for 2 sec.
Pairing Your Bike Light with Your Edge 830 or 1030 1 Bring the Edge device within range (1 m) of the sensor. NOTE: Stay 10 m (33 ft.) away from other ANT+ ® bike lights while pairing. 2 Turn on the Edge device. 3 Select >...
Light Mode Settings From the Sensors menu, select Lights > Network Options > Light Mode. Auto: Automatically adjusts the light intensity and light mode based on the ambient light and time of day. High Visibility: Sets the light intensity to flash mode or the brightest setting available. Trail: Automatically adjusts the light intensity and light mode based on the ambient light and time of day.
100 to 300 lm Up to 6 hr. Day flash 700 lm Up to 25 hr. The device withstands incidental exposure to water of up to 1 m for up to 30 min. For more information, go to www.garmin.com/waterrating. Device Information...
• Connect the charger securely to the device. You can charge the device by plugging the USB cable into a Garmin approved AC adapter with a standard wall outlet or a USB port on your computer. Charging a fully depleted battery takes about 6 hours using a computer and 4 hours using an AC power source.
This provides easy access to these services for Garmin devices: • Software updates • Product registration Getting More Information • Go to support.garmin.com for additional manuals, articles, and software updates. • Go to buy.garmin.com, or contact your Garmin dealer for information about optional accessories and replacement parts. Troubleshooting...
Other Compatible Devices Pairing Your Bike Light with Another Edge Device 1 Bring the Edge device within range (1 m) of the sensor. NOTE: Stay 10 m (33 ft.) away from other ANT+ bike lights while pairing. 2 Turn on the Edge device. 3 From the Sensors menu, select Add Sensor >...