Table of Contents
Advertisement
(ZLSv70Z2
"ON)
8-1
TUNER
ENTRY
The Display
and
The Indicators
Caution:
Too LOUD!
ToT
Radlo
Active BASS Effect
The richness and fullness of the sound is maintained regardless of how high or low you set the VOLUME control.
To get the effect, press ACTIVE BASS EX so that the indicator on the button lights up.
To cancet the effect, press the button again so that the indicator goes off.
Using the Tuner Entry Function
With Tuner Entry on, the Unit automatically shifts to the most recently played radio station when tape or CD play ts
over.
To eet the function, press TUNER ENTRY so that "TUNER ENTRY" appears on the display.
To cancel the function, press the button again so that "TUNER ENTRY" disappears.
( In the following situations, even if Tuner Entry is on, it will not take effect:
«
When you intentionally stop the CD player or tape deck by pressing ™/CLEAR on the CD player or Mon the
tape deck.
.
°
After the cD player ¢ or tape deck stops playing while Auto Power Off (sce page 18) is on.
+
When the tape deck is in Reverse Mode (see page 12).
Listening with Headphones
A pair of headphones can be connected to the PHIONES jack on the front panel. Be sure to turn down the volume before
connecting or putting on headphones, as high volume can damage both the headphones and your hearing.
The Display and the Indicators—Two Very Useful Hints
LU The display tells you many useful things about what your Unit is doing. Watch it as you give instructions by
pressing buttons. It also gives you some messages like "NO DISC," "NO TAPE,"
and some others to show you
what to do next.
Some of the controls have a small tight, called an indicator, right next to or even right on the button or knob itself.
The light comes on when Ine Function i is on, and a eoes off when it is not in use.
CAUTION: Aiways set the VOLUME control to MIN before suing on aconnected source such as a VER ¢ oY -]
|
turntable, or starting any other of the sound sources such as the radio, tape, or CD player. Otherwise, if the |
VOLUME control is turned up, the sudden blast of sound energy can permanently damage your a
and/
or ruin your speakers.
Listening to the Radio
You can listen to both AM (MWILW) and FM.
Ql] Before listening to the radio, check that both the AM (MW/LW) and FM antennas are firmly connected.
U To listen to the radio after CD or tape play, see "Using the Tuner Entry Function," above.
One Touch Radio
Just press AM (MW/LW) to tur on the Unit and stast playing the most recent AM (MW/LW) station tuncd in, or press
FM to start the most recent FM station tuned in.
Q You can switch [rom any other sound source to the radio by pressing either AM (MW/LW) or FM.
Page 8
Tuning in a Station
Press AM or FM to tum on the radio. The display shows the station frequency tuned to.
Three ways totune
Three ways to select a station
in a station
1. Press TUNING < of > repeatedly to move from frequency to frequency until you find the one you want.
OR
2. Hold down TUNING < or >, the frequency starts changing on the display. When a station is tuned in, "TUNED"
lights up on the display and the frequency stops changing.
OR
3, Press once and release PRESET < or > tu go to the next preset stalion, or hold P RESET < or > to cycle through
the presct stations: release the button when the presct station you want shows on the display. (This method is
possible only after presetting stations.)
You can also use the Remote to tune in stations and preset channels:
To tune presetected stations with the Remote:
1. Press FM or AM depending on which band you want.
2. Select the station by entering the presct channel number in the 10 key pad of the Remote.
Presetting Stations
How to preset AM
Once a station is assigned to a channel number, the station can be quickly tuncd cither from the Remote using the 10
and FM radio
key pad of the Remote or the GA-S30BK itself using PRESET
< or > to cali up the channel number.
stations
E) You can preset 40 AM (MW/LW) and FM stations at random.
i) Preset stations may be erased when powcr is cut off to the Unit, as when il is unplugged from the AC outlet or
TUNING
~ apower [failure occurs. If the presct stations are lost, simply set the stations again using the following procedure.
To a
radio stations
. Tune in the station you want to set using
TUNING <or >.
Press MEMORY.
On the display "MEMORY" will blink for 8 seconds.
oO During these 8 seconds while "MEMORY" is blinking you can assign a channel number to the station and
mC)
enter it inte the memory.
dm
3. Sclect a channel number by pressing PRESET < or > until you find the channel number you want,
©
MEMORY
4. Press MEMORY and the station will be assigned to the channel number showing on the display.
© Ifastation has been previously stored using the same channel number, it will be erased and the newly sclected
station will be stored,
PRESET
O®
ey
memony (
:
Receiving in Stereo or Mono
When an FM stereo broadeast is hard to receive or noisy:
idler
(Press FM MODE/MU" TE on the remote control so that reception improves, although you loose the
stereo effect. In this state, you wifl hear noise while tuning into stations.
Q) To restore stereo effect, press FM MODE/MUTE again so that "AUTO" appears on the display.
in this state, when a program is broadcast in stereo, you will hear stereo sound; when in monaural,
you will hear monaural sounds. Furthermore, in this state, you won't hear nvise while tuning into
stations.
Page 9
MAOES-VO
Advertisement
Table of Contents
