Pioneer RX-722 Operating Instructions Manual

The Models, PL-222Z, PL-322AZ and PL-322Z are not sold in the U.S.A.
Thank you for buying this Pioneer product.
Please read through these operating instructions so you wilt
know how to operate your model properly. After you have fi-
nished reading the instructions, put them away in a safe place for
future reference.
In some countries or regions, the shape of the power plug and
power outlet may sometimes differ from that shown in the
explanatory drawings. However, the method of connecting and
operating the unit is the same.
WARNING: To prevent FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT NOTICE
[For U.S. and Canadian models]
The serial number for this equipment is located on the rear panel.
Please write this serial number on your enclosed warranty card
and keep it In a secure area. This is for your security.
[For Canadian models]
UFO N+-To prevent etEcTRIC SHOCK DO-NOT-USE-
THIS |POLARIZEDIPLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN 8E
FULLY INSERTED TO PREVENT BLADE EXPOSURE.
ATTENTION: our. pREVENIR' LES cCHOCS
ELECTRIQUES NE PAS UTWLISER CETTE FICHE POLARISEE
AVEC UN PROLONGATEUR UNE PRISE DE COURANT OU UNE
AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT
ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A
DECOUVEAT.
TWO VOLTAGE SELECTOR SWITCHES
Only muiti-voltage modets are provided with these switches.
U.S, and Canadian models are not provided with these switches.
Mains voltages in Saudi Arabia are 127V and 220V only.
Never use this made! with 110¥V setting in Saudi Arabia.
CHECKING ACCESSORY ITEMS
BEFORE OPERATION .........
ANTENNA CONNECTIONS
CONNECTIONS E
PANEL FACILITIES 2... 262-222 s005
REMOTE CONTROL UNIT FACILITIES
TURNTABLE FACILITIES. ..........
GRAPHIC EQUALIZER CONTROLS .. d i g o a i e e e
PRELIMINARY OPERATIONS... .. 2-2-2022 -0 222 - eee eee
CONTENTS
The line voltage selector switches are on the rear panel. Before
your model is shipped from the factory, these switches are set to
the power requirements of the destination. Check they are set
properly before plugging the power cord into the household wail
socket. if the voltage is not properly set or if you move to an area
where the voltage requirements differ, adjust the selector
switches as follows.
1. Use a medium-size screwdriver.
2. First, insert a screwdriver into the groove of the voltage
selector at the top, and adjust so that tip of the groove points
to the voltage vaiue of your area
3. Next, insert the screwdriver into the groove of the voltage
selector at the bottom and adjust until the voltage is the same
as at the top.
Both switches must
be in the same switch
setting.
CHANNEL-STEP-SWIFCH
Oniy multi-voltage models are provided with this switch.
U.S. and Canadian models are not provided with this switch:
(This switch is on the rear panel.)
The unit has been factory preset to the channel allocation for the.
area in which it is to be sold, }f the value is set incorrectly, the
frequency display may stop at the wrong frequency, or sound
may be distorted, resulting in an inability to reproduce reception
signais at their proper sound quality.
For this reason, be sure to confirm that the valué is set correctly
before first using the. unit.
{190 kHz/10 kHz] position:
Set to this position for areas with FM
reception step of 100 kHz, AM 70 FM/AM
kHz. : I } 50/9KHz
{50 kH2z/9 kHz} position: i 100/10 KHz |
Set to this position for areas with FM
reception step of 50 kHz, AM 9 kHz.
When unsure about the channel allocation for your area, consult
your dealer for correct information.
CHANNEL |
USING THE OPTIONAL AUDIO TIMER
MAINTENANCE .....-.---4--5--0405--
TROUBLESHOOTING ......- 2
SPECIFICATIONS . 2.0.02. eee eee
HOW TO HANDLE CASSETTE TAPES
Q) PIONEER'
The future of sound and vision.