A2 or Nicam A2 or Nicam Auto Stereo Equalizer Front/Side AV Jack PC Input(VGA) Scart Jack 2Scart 2Scart Back A/V Monitor Out Jack S-VHS Jack(Front only) Head/Earphone Jack Common Interface Service Port Normal Remocon Accessory Battery Matching Trans Rod ANT Samsung Electronics...
4. When replacing the Side AV Ass'y : No adjustments required 5. When replacing the PIP Module : No adjustments required 6. When replacing the Control Ass'y : No adjustments required 7. When replacing the PFC Ass'y : No adjustments required Samsung Electronics...
9.TTX Flof/List Flof Flof 10.Tilt 11.LNA 12.DNIe JR 13.Hotel Mode 14.PIP By MODEL 2. Option2 South East Asia 21"/SLIM-CRT 21"/SLIM-CRT Remark Non-PIP/LNA Non-PIP/Non-LNA Option2 1.X-Ray Protect 2.HighDeviation 3.V-Guard 4.Sound Carrier Mute 5.Speaker By MODEL 6.PIP Device SDA9488 SDA9488 7.ZOOM Samsung Electronics...
Page 12
16:9 H Trapezium Adjust 14:9 V Amp Adjust 14:9 V Shift Adjust 14:9 H Parabola Adjust 14:9 H Trapezium Adjust VM Mode VM Gain VM Delay Preset Gain R Preset Gain G Preset Gain B Blue Screen HS Of Samsung Electronics...
Page 14
YUV Sub Tint RF YUV Sub Tint AV YUV Sub Tint RGB Blue Stretch Soft Clipping Level Peak White Limit SECAM B-Y Offset Peakng CF0 & Delay Mode Sub Sharpness-RF Video Dependent Coring RF Video Dependent Coring AV Samsung Electronics...
Page 15
Item Adjust S-Asia Remark Bypass of Chroma Base Band Fixed Beam Current Fixed Beam Current1 Forced Colour On Sync Performance Trick Mode Beam Current Limiting Comb Filter RGB Comb Filter Chroma Trap Mode EHT Tracking Mode AV FOA/FOB Samsung Electronics...
Page 16
Ratio Pre & After Shoot Ratio posi & Nega Peaks Dynamic Skin Control Gamma & White Stretch DNIE JR Comb Filter Diode Clamp DC Transfer Ratio NTSC Matrix S-Asia Remark WHITE BALANCE 286/290 40FL 265/265 45FL 286/290 2.0FL 265/265 2.5FL Samsung Electronics...
② Press "Power Off →Info → Menu → Mute → Power On" using the remote control and enter Factory Mode. ③ Enter Deflection Mode. ④ Adjust the V-AMP, V-SHIFT, H-AMP and H-SHIFT items so that the width becomes 5 and the height becomes 4. Samsung Electronics...
Page 18
⑦ When the adjustments are complete, display the Lion pattern and check that the picture size has not been changed. If there is no change, finish the adjustments. 3-10 Samsung Electronics...
1. To enter Service Mode, press the keys on the remote control according to the following sequence. (in Stand-by status) Info → Menu → Mute → Power On 2. When entering Service mode, the software information is displayed at the top of the service mode menu OSD. ex) T-HITPEU-1000 2005/0X/XX Samsung Electronics 3-11...
Page 20
- Check the “Flash selection” item is appoint “Manual” - You can adjust program delay time for program speed but we use the normal “5[ms]” - Check the green lamp if this is sometime red lamp you can not programming 3-12 Samsung Electronics...
Page 21
- Click the “Erase Flash” button for before program erase - You can select flash selection item but we use normal “All” mode - Change the “Select flash ROM to erase. When ready press Send.” - Click the “Send” button Samsung Electronics 3-13...
Page 22
- Click the “Browse” button and find the new program folder in your computer - Click the “Send” button 6. Verify new program - Click the “Verify Flash” button - Change the “Select flash to verify correct programming. When ready press Send.” - Click the “Send” button 3-14 Samsung Electronics...
4. Slowly turn the Static Focus VR counter clockwise so that the center vertical line is the most clearly displayed. [adjusted point : Center(2/1)] SINGLE FOCUS VR 5. Check the entire screen focus and repeat steps 3 to 4, if necessary. Samsung Electronics 3-15...
Page 24
2. Initialize all settings to the values appropriate to the corresponding model. 3. Display the Toshiba pattern. 4. First check IBRM in "G2 Adjust" of Factory and adjust Screen VR until the color of IBRM item turns green. SCREEN 3-16 Samsung Electronics...
Page 25
4. When the adjustment is finished, check the following checklist. - If there is a spot on the screen when turning the TV set off/on, adjust the Screen Voltage again. - If there is a ghost line on the screen, adjust the Screen Voltage again. Samsung Electronics 3-17...
Page 29
Schematic Diagram 10. Schematic Diagram 10-1 MAIN TP04 This Document can not be used without Samsung’s authorization. TP06 TP12 TP07 TP09 TP11 TP09 TP06 TP04 TP10 TP07 Power TP10 Signal TP11 TP12 Samsung Electronics 10-1...
Page 30
Schematic Diagram 10-2 POWER This Document can not be used without Samsung’s authorization. TP01 Power TP03 Signal TP02 TP02 TP03 TP01 TP08 TP05 TP08 TP05 10-2 Samsung Electronics...
Page 31
Schematic Diagram 10-3 SOUND This Document can not be used without Samsung’s authorization. Power Signal Samsung Electronics 10-3...
Page 32
Schematic Diagram 10-4 CRT This Document can not be used without Samsung’s authorization. Power Signal 10-4 Samsung Electronics...
Page 33
* CN501 : A 9 pin port connected to the CRT ASSY, which outputs the R/G/B signal to the CRT ASS'Y for display and Power signals to the CRT DRIVE. * CN701 : A 8 pin port connected to the AV ASSY, which receives AV2 external input. Samsung Electronics...
Page 34
Pin Name PIN No. Pin Name CN501 CN701 Connected to the CRT ASSY Connected to the AV ASSY PIN No. Pin Name PIN No. Pin Name B+200V L-IN R-IN HEATER L-OUT R-OUT SENSE V-IN R-OUT G-OUT V-OUT B-OUT Samsung Electronics...
Page 35
* CN502 : The R/G/B output signal from the UOC Module & the power, which is required to drive the CRT and the AMP, from the DEFLECTION BLOCK is connected to this port. 9-2-3 CRT Board Connector Pin CN502 Connects the R/G/B signal from the UOC Module. PIN No. Pin NAME B+200V HEATER SENSE R-OUT G-OUT B-OUT Samsung Electronics...
Page 37
③ Tap the upper part of the Back Cover 2 or 3 times and pull the Back Cover to separate it from the unit. Notice: Disassemble the product after disconnecting the power cord and discharge the unit to prevent an electric shock and damage to the product due to static electricity. Samsung Electronics 12-1...
Page 38
Press the clip down completely and pull the con- nector. ① Separate theAV and Main Board from the Front Cabinet and AV Wire, GT-Pin Wire. ② To separate the Wire, Fixing clip and pressing the Wire. 12-2 Samsung Electronics...
Page 39
① Separate the cables connecting the FBT and the CRT. Notice: Since there may be a remaining high-voltage current within the CRT, take care not to touch the CRT hole with metal or a part of yourself when separating the cables. Samsung Electronics 12-3...
Page 40
In addition, separate the wires on a flat and clean surface so as to prevent scratching of the material and the PCB. Pull the wires while pressing on the fixing clip. 12-4 Samsung Electronics...
Page 41
Operation Instruction & Installation 11. Operation Instruction & Installation 11-1 Product Features and Functions 11-1-1 Front 11-1-2 Side 11-1-3 Rear cable television network Samsung Electronics 11-1...
Page 42
SOURCE external input mode. Used to display all of the available video sources. SLEEP Used to select a preset INFO time interval for Used to view the automatic shut off. channel information and setting status you selected. 11-2 Samsung Electronics...
Page 43
When Check the AC power cord for possible damages. Keep voltage exceeds the specified limits, check each special the part or the lead away from any heat-emitting part. materials. Samsung Electronics...
Page 44
Critical safety parts should be bracketed with ( Use only regular parts for replacements (in particular, flame resistance and dielectric strength specifications). Irregular parts or materials may cause electric shock or fire. Samsung Electronics...
Page 45
5. Check for insulation between the blade of the AC plug 10. The sharp edges of the metal material may cause and that of any conductive materials (i.e. the metal physical damage, so ensure wearing protective gloves panel, input terminal, earphone jack, etc). during the repair. Samsung Electronics...
Page 46
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Samsung Electronics...
Page 47
5. Make sure to turn the power off and unplug the power cord from the outlet before repositioning the product. Also check the antenna cable or the external connectors if they are fully unplugged. Damage to the cord may cause fire or electric shock. Samsung Electronics...
Page 49
2) Check that the Master Switch has been pressed. 3) Check that the transmitter is turned on. 4) Check that transmitter device selection is set to TV. 5) Check that the signal cable is properly connected. 6) Check that channel setting has been set. Samsung Electronics...
Page 50
” S “ e ” S r i a c i p & i l + D “ ( ” 1 t r a D “ ” 1 Q “ ” 1 Q “ ” 1 r i a Samsung Electronics...
Page 51
Cannot select an A/V channel. out, you cannot select an A/V channel. Check if the connector is properly connected. Cannot select a menu. Check if the menu is grayed out. If a menu is grayed out, it cannot be selected. Samsung Electronics...
Page 52
■ Set the auto volume control to ON. There is a lot of noise. Keep the antenna away from the power cord or connectors if possible. The selected language does not Press the Multiplex button to select the TV. appear. Samsung Electronics...
Page 53
This noise may occur when the plastic material inside the TV expands or contracts according The TV makes a noise as if to the seasonal temperature or humidity. This is like the noise from a furniture/cabinet/sink something is dropping inside. unit, and there is no need for concern. Samsung Electronics...
Page 54
Therefore, you can determine whether the software has been properly downloaded, if you know the correct checksum for that version of the software. You can check the checksum according in the following order. Factory Mode → Checksum → Right Button → Calculate Checksum → Output Checksum (e.g. 3036) ■ Checksum Examples T-HITPEU-1000:checksum=5B67 T-HITPEA-1000:checksum=51A7 Samsung Electronics...
Page 55
The mirror returns to a blank state so that no stains or after-images are left. The SAMSUNG SKY500N model has both an ANYNET port and a SERVICE jack port. Because the shape of the ANYNET port on the DLP TV is the same as that of the SERVICE jack port of the SKY500N, it fails to turn the TV off after a connection has been reported.
Page 56
Ex: For LCD 15:9 devices, "Wide" is displayed on the OSD instead of "16:9". 4. The picture size can be changed even in the blue screen. However, the picture size should be controlled by the product specifications if the change is impossible due to hardware restrictions. 14-2 Samsung Electronics...
Page 57
You can use this AV interface for users by controlling connected AV devices function to study English by watching AFKN or CC marked through the Anynet menu when AV devices of Samsung video tapes. Electronics are connected.
Wiring Diagram 8. Wiring Diagram 8-1 Overall Wiring SI GN A L MAIN P OW E R AV Signal Audio Out CRT Power Supply & Main Input SPEAKER Samsung Electronics...
Page 73
Electrical Part List 5. Electrical Part List 5-1 CW21Z413NCXXEC You can search for the updated part code through ITSELF web site. URL:http://itself.sec.samsung.co.kr Loc.No. Code No. Description Specification Q'ty SA/SNA Remark ASSY CHASSIS M0017 AA91-09967A ASSY CHASSIS CW21Z403NCXXEC,TH,ELDOR S.N.A M0014 AA94-15923A...
Page 85
Exploded View & Part List 4. Exploded View & Part List 4-1 CW21Z413NCXXEC You can search for the updated part code through ITSELF web site. URL:http://itself.sec.samsung.co.kr Loc.No. Code No. Description Specification Q'ty SA/SNA Remark M0006 CIS7 AA61-60003J SPRING ETC-CS -,SUS304,-,-,OD6,N7,OD6,-, S.N.A...