Button Descriptions; Ontrolling The Mplifier Peaker River - X10 SoundPower VK59A Owner's Manual

C C C C C VR32A A VR32A A
VR32A A VR32A A VR32A A
ONTROLLING ONTROLLING ONTROLLING THE THE THE THE MPLIFIER MPLIFIER MPLIFIER
ONTROLLING ONTROLLING THE MPLIFIER MPLIFIER
Press and release the AUDIO button. The LED blinks once. Then press
and release button 4 (AMP). This puts the remote into the mode to
control the VR32A Wireless Amplifier/Speaker Driver.
2. 2. 2. 2. 2. Press and release
button 4 (AMP).
navigation button
to increase bass,
DOWN to
decrease bass.
7. 7. 7. 7. 7. Press RIGHT
8. 8. 8. 8. 8. Press OK to restore
the default settings
for balance, bass,
and treble.
1 4 1 4
1 4 1 4 1 4
/S /S D D D D D
/S /S /S
PEAKER PEAKER PEAKER RIVER RIVER RIVER
PEAKER PEAKER RIVER RIVER
1. 1. 1. 1. 1. Press and release the
AUDIO button. The
LED blinks once.
3. 3. 3. 3. 3. Press VOL+ to
increase volume on
both channels; VOL-
to decrease volume
on both channels on
the VR32A
Amplifier/Speaker
Driver.
4. 4. 4. 4. 4. Press CH+ to adjust
balance to right
channel, reduces left
channel volume; CH-
to adjust balance to
left channel, reduces
right channel volume.
5. 5. 5. 5. 5. Press MUTE to toggle
the audio output
ON/OFF.
6. 6. 6. 6. 6. Press the UP
navigation button to
increase treble, LEFT
to decrease treble.
S S S S S TV TV , VCR, C , VCR, C , , , , ,
TV, VCR, C TV TV , VCR, C , VCR, C
ETTING ETTING UP ETTING UP UP FOR UP FOR FOR FOR ABLE ABLE ABLE AND AND AND
ETTING ETTING UP FOR ABLE ABLE AND AND
1. 1. 1. 1. 1. Turn on the device you want to control (TV, VCR,
cable box, etc.).
2. 2. 2. 2. 2. Press and hold SETUP until the LED indicator
lights steadily. Release the SETUP button.
3. 3. 3. 3. 3. Press and release mode button for the device
you want to control (TV, VCR, Cable or AUX).
The LED blinks once. (See notes below).
4. 4. 4. 4. 4. Enter the 3 digit Code from the Librar y Code
Table (separate sheet). The LED turns off after
the last digit entered.
5. 5. 5. 5. 5. Point the remote at the device and press the
POWER button. Your device should turn off.
6. 6. 6. 6. 6. Turn your device on and press CHANNEL+. If
the device responds, setup is complete.
Notes:
1. The TV mode key can only be used to store TV codes but you can
store a code for ANY device under either the VCR, CBL, or AUX
mode key. E.G., you can store a Cable code under the VCR key, or
a Satellite code under the Cable key, etc.
2. If your TV/VCR/Cable Box does not respond, tr y the other codes
for your brand. If it still doesn't respond, try the Code Search
method on page 16.
3. If the LED blinked rapidly when you entered the code, you may
have entered an invalid code. Recheck the code in the code list
(separate sheet) and tr y again.
4. If some buttons do not operate your equipment, try one of the
other codes for your brand.
5. When searching for a code (page 16) you might have to press
CHANNEL+ many times (50+). If the device does not have a
Channel Up function, use the PLAY button (VCR only) or the
POWER button.
1 5 1 5
1 5 1 5 1 5
AUX AUX
AUX AUX AUX