Roubleshooting; Code - X10 SoundPower VK59A Owner's Manual

T T T T T

ROUBLESHOOTING

ROUBLESHOOTING ROUBLESHOOTING
ROUBLESHOOTING ROUBLESHOOTING
T T T T T R R R R R ' ' ' ' ' A/V A/V A/V A/V A/V
HE HE HE EMOTE EMOTE WON EMOTE WON WON WON T T T T T CONTROL CONTROL CONTROL CONTROL YOUR YOUR YOUR YOUR
HE HE EMOTE EMOTE WON CONTROL YOUR
: : : : :
ALL ALL ALL ALL ALL
• Use manual controls or the original remote control to confirm the
equipment is working properly.
• Be sure you pressed the device key for the device you want to
control.
• Reenter the code for your A/V product from the code listings on
the separate sheet included.
• Try searching for codes as described on page 16.
• Replace the Remote's batteries.
T T T T T R R R R R ' ' ' ' ' VR32A W VR32A W VR32A W VR32A W VR32A W
HE HE HE HE HE EMOTE EMOTE EMOTE EMOTE EMOTE WON WON WON WON WON T T T T T CONTROL CONTROL YOUR CONTROL CONTROL CONTROL YOUR YOUR YOUR YOUR
D D D D D : : : : :
RIVER RIVER RIVER RIVER RIVER
• Make sure your press the Audio button then the AMP button
(button 4) before you try to control the VR32A.
• If you have reprogrammed the Audio button to control something
else, program it back to Audio operation as follows:
The default code for the Audio button is 013. You might want to
change this to use the Audio button to control something else, like a
Laser Disk player, for example. Note however that if you do this the
Audio button will not let you access the MP3, DVD, CD, and AMP
functions (1, 2, 3, 4 buttons). To reprogram the Audio button to once
again access these functions:
1. Press and hold SETUP until the LED indicator remains on.
2. Release SETUP.
3. Press and release the Audio button.
4. Enter the 3 digit code 0, 1, 3.
5. The LED indicator turns off after the last digit is entered.
2 6 2 6
2 6 2 6 2 6
, , , , , ' ' ' ' '
EQUIPMENT EQUIPMENT EQUIPMENT OR OR DOESN OR DOESN DOESN DOESN T T T T T WORK WORK A A A A A T T T T T WORK WORK
EQUIPMENT EQUIPMENT OR OR DOESN WORK
A A A A A /S /S /S /S /S
IRELESS IRELESS IRELESS IRELESS IRELESS MPLIFIER MPLIFIER MPLIFIER MPLIFIER MPLIFIER PEAKER PEAKER PEAKER PEAKER PEAKER
I I I I I
F F F F F YOU YOU YOU YOU ARE ARE ARE ARE NOT NOT NOT GETTING NOT GETTING ANY GETTING GETTING ANY ANY ANY SOUND SOUND SOUND SOUND A A A A A T T T T T ALL ALL ALL ALL FROM
YOU ARE NOT GETTING ANY SOUND ALL
• Check that the CHANNEL slide switch (labeled A, B, C, D) on both
units is set to the same letter.
• Check that both the transmitter and receiver's power supplies are
plugged in. Check that the ON/OFF switch on the transmitter and
receiver are ON.
I I I I I , , , , ,
F F F F F THE THE SOUND THE THE THE SOUND IS IS IS IS IS POOR SOUND SOUND SOUND POOR POOR POOR POOR OR OR OR THERE OR OR THERE THERE IS IS IS IS IS INTERFERENCE THERE THERE INTERFERENCE INTERFERENCE INTERFERENCE INTERFERENCE
• Try changing the channel on both units. Do this by adjusting the
CHANNEL slide switch on each unit to any position (A, B, C, or D).
• Make sure both units are set to the same letter. Try repositioning
the antenna on each unit.
T T T T T T T T T T M M M M M ' ' ' ' '
HE HE HE HE HE RANSCEIVER RANSCEIVER RANSCEIVER RANSCEIVER RANSCEIVER ODULE ODULE ODULE ODULE DOESN ODULE DOESN DOESN DOESN DOESN T T T T T RESPOND RESPOND TO RESPOND RESPOND RESPOND
• Check the House Code on the Transceiver Module is set to 'A.' If
you have changed the House Code on the remote (see p. 22),
check that it matches the House Code on the Transceiver Module.
• Press the ON/OFF button on the front of the Transceiver Module
to confirm it operates the equipment connected to it.
T T T T T T T T T T M M M M M , , , , ,
HE HE HE HE HE RANSCEIVER RANSCEIVER RANSCEIVER RANSCEIVER RANSCEIVER ODULE ODULE ODULE WORKS ODULE ODULE WORKS WORKS WORKS WORKS BUT BUT BUT OTHER BUT BUT OTHER OTHER OTHER MODULES OTHER
• Check that the Module has the same House Code as the
Transceiver Module.
• Try plugging the Module into a different outlet.
Note: if you use an RF Transceiver (such as the RR501 or TM751) to
control X10 Modules, you will be able to control up to 16
Modules. With a Transceiver, when you press 1-6-ON you turn on
Module number 16. However, if you use an IR543, when you
press 1-6-ON you turn on Modules 1 AND 6. The IR543 can only
control 10 Modules (1-9 plus 0=10).
2 7 2 7
2 7 2 7 2 7
VR32A VR32A VR32A VR32A VR32A
FROM THE FROM FROM THE THE THE
FROM THE
: : : : :
TO TO TO TO THE THE THE THE THE REMOTE REMOTE REMOTE REMOTE REMOTE
' ' ' ' ' : : : : :
MODULES MODULES MODULES MODULES DON DON DON DON DON T T T T T RESPOND RESPOND RESPOND RESPOND RESPOND