Advertisement
Quick Links
Advertisement
Related Manuals for NCR 7358-K036
Summary of Contents for NCR 7358-K036
- Page 1 Kit Instructions uNAV Input Device 7358-K036 Issue A...
- Page 2 NCR, therefore, reserves the right to change specifications without prior notice. All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR office for information that is applicable and current.
-
Page 3: Revision Record
Revision Record Issue Date Remarks Mar 2020 First Issue... - Page 4 • NCR SelfServ™ Checkout (7350) • NCR SelfServ™ Checkout (7350) R6 Lite • NCR FastLane SelfServ™ Checkout (7358) Note: For the purpose of illustration only, this publication shows images using an NCR FastLane SelfServ™ Checkout (7358) R6L Plus unit.
-
Page 5: Kit Contents
Input Device Kit Contents Part Number Description 497-0527746 7358-K036 uNav Input Device Kit 497-0526011 Bracket - uNav Mounting Bracket 497-0526010 Bracket - uNav Housing 006-8626235 Screw, M3 x 5, Steel, Flat Head, Phillips, Black Oxide (2 pcs) 009-0032884 Cable Assembly – USB A to Mini-B 90 Degree Up (4000... -
Page 6: Installation Procedures
uNav Input Device Installation Procedures To install the uNav device, follow these steps: 1. Do the following: a. Connect the USB cable to the uNav device. b. Secure the uNav device to the uNav housing using three (3) nuts, as shown in the image below. - Page 7 uNav Input Device 2. Route the other end of the uNav cable through the hole on the uNav mounting plate. 3. Hook the uNav mounting plate to the slot on the bottom of the uNav housing, as shown in the image below.
- Page 8 uNav Input Device 4. Secure the uNav housing to the uNav mounting plate using two (2) screws, as shown in the image below. 5. Depending on the currency configuration of the SelfServ Checkout unit, place the drilling guide on the Core Door, as shown in the image below.
- Page 9 Core Door. b. Clean the Core Door to remove any drilling debris. For more information on properly cleaning the Core Door, refer to NCR FastLane SelfServ™ Checkout (7358) Hardware Service Guide (BCC5-0000-5265). 8. Feed the uNav cable through the drilled hole, as shown in the image below.
- Page 10 uNav Input Device 9. Remove the protective film of the double-sided tape around the uNav mounting plate and then attach the uNav device to the Core Door, as shown in the image below. Note: For the purpose of illustration only, the image below shows a Full Recycling configuration unit.
- Page 11 13. Turn on the SelfServ Checkout unit. The ADD/CADD window is displayed, showing available devices. Note: The NCR FastLane SelfServ™ Checkout application automatically runs and installs all available devices. If the new or replaced device is not listed in the ADD/CADD window, an error message is displayed. Follow the instructions on how...
- Page 12 Input Device Routing cables of Core Door Components When servicing R6L Plus Core Door components, NCR recommends routing their cables together for proper bundling and cable dressing. To route the cables of Core Door components, follow these steps: Note: Ensure that all cables of the Core Door components are installed before applying zip ties.
- Page 13 uNav Input Device 2. Through the Cable Access Hole, continue routing the cables up the rear of the Core Cabinet wall and into the Receipt Printer side of the unit as shown below.
- Page 14 uNav Input Device 3. From the Upper Cabinet frame, use cable ties to do the following: a. Wrap the cables and then tie them on corresponding lance bridges to fix the cables on the Upper Cabinet frame as shown in the image below. b.