Bosch Professional GWX 180-LI Original Instructions Manual page 20

20 | English
Technical data
Angle grinder
Article number
Rated voltage
A)
Rated speed
Max. grinding disc diameter
Restart protection
Run-out brake
Soft start
Weight according to EPTA-Procedure 01:2014
– with low-vibration auxiliary
handle
– with standard auxiliary
handle
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
C)
ure during operation and
during storage
Compatible rechargeable bat-
teries
Recommended rechargeable
batteries
Recommended chargers
A) Rated speed in accordance with EN 60745-2-3
B) Depends on battery in use
C) Limited performance at temperatures < 0 °C
Noise/Vibration Information
Noise emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise level of the power tool are: 87
dB(A); sound power level 98 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
Surface grinding (roughing):
2 2
a = 9.0 m/s , K = 1.5m/s ,
h
Disc sanding:
2 2
a < 2.5 m/s , K = 1.5 m/s .
h
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
tion.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
1 609 92A 6CY | (14.07.2021)
antly increase the exposure to vibration over the total work-
ing period.
GWX 180-LI
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
3 601 JH9 1..
tually being used should also be taken into account. This can
V= 18
significantly reduce the exposure to vibration over the total
-1
min 11.000
working period.
mm 125
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
●
power tool and application tools, keeping the hands warm,
–
and organising workflows correctly.
●
B)
Fitting
kg 2.4–3.2
Charging the battery
kg 2.3–3.0
u
°C 0 to +35
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
°C –20 to +50
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
GBA 18V...
does not damage the battery.
ProCORE18V...
The lithium-ion battery is protected against deep discharge
GBA 18V... ≥ 4.0 Ah
by the "Electronic Cell Protection (ECP)". When the battery
ProCORE18V...
is discharged, the power tool is switched off by means of a
≥ 5.5 Ah
protective circuit: The application tool no longer rotates.
GAL 18...
u
GAX 18...
GAL 36...
Follow the instructions on correct disposal.
Removing the Battery
The battery (5) is equipped with two locking levels to pre-
vent the battery from falling out if the battery release button
(6) is pressed unintentionally. As long as the battery is inser-
ted in the power tool, it is held in position by means of a
spring.
To remove the battery (5), press the release button (6) and
pull the battery out of the power tool. Do not use force to
do this.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
to
Bosch Power Tools