Advertisement
Available languages
Available languages
EN
SHUT DOWN/TRANSPORTATION (Fig. A)
1. Turn on/off switch
to the OFF position.
3
2. Unplug the unit.
3. Store the power cord
2
handle/cord wrap
1
as shown.
4. When transporting in vehicles, secure the
machine.
MAINTENANCE
The DEWALT appliance has been designed to
operate overall long period of time with a minimum
of maintenance.Continuous satisfactory operation
depends upon proper appliance care and regular
cleaning.
WARNING: To reduce the risk of injury, turn
appliance off and disconnect appliance from
power source before installing and removing
accessories, before adjusting or changing set-
ups or when making repairs. An accidental start-up
can cause injury.
WARNING: For user servicing, the machine must
be dismantled, cleaned and serviced, as far as is
reasonably practicable, without causing risk to the
maintenance staff and others. Suitable precautions
include, decontamination before dismantling,
provision for local filtered exhaust ventilation
where the machine is dismantled, cleaning of the
maintenance area and suitable personal protection.
• The manufacturer, or an instructed person, shall
perform a technical inspection at least annually,
consisting of, for example, inspection of the filter for
damage, air tightness of the machine and proper
function of the control mechanism.
• When carrying out service or repair operations, all
contaminated items which cannot be satisfactorily
cleaned, are to be disposed of; such items shall
be disposed of in impervious bags in accordance
with any current regulation for the disposal of such
waste.
• For dust extractors it is necessary to provide for
an adequate air change rate L in the room if the
exhaust air is returned to the room.
NOTE: Refer to national regulations is necessary.
FILTER (Fig. A, H, I)
FILTER CARE
The filters included with this vacuum are long life
filters. To be effective in minimizing dust recirculation,
the filters MUST be installed correctly and in good
condition.
WARNING: Appropriate personal protective
equipment like dust mask and gloves should be used
while handling the filters.
TO REMOVE FILTERS
1. Turn on/off switch
3
to the OFF position ( O ) and
unplug cord from outlet.
2. Release lid latches
5
és vegye le a and remove
vacuum head
4
from canister. Place vacuum
head on a level surface upside down.
3. Turn each filter
counterclockwise by gripping it
9
on the plastic end cover as shown, and carefully
wrapping it around the top
remove from head, ensuring debris does not fall
into mounting hole.
NOTE: Use care to not damage filter material.
4. If the bottom side of the vacuum head needs to
be cleaned, use a cloth dampened with water and
mild soap and allow it to dry. Dispose the cloth in
an appropriate container.
5. Inspect filters for wear, tears or other damage.
NOTE: If there is any doubt on the condition of the
filters they MUST be replaced. DO NOT continue
use if filters are damaged.
WARNING: Never use compressed air or a
brush to clean filters, otherwise damage to the filter
membrane will occur which will allow dust to pass
through the filter.
If needed, gently tap against a hard surface or rinse
with room temperature water and let air dry. Cleaning
of the filters is typically unnecessary, even if the filter
is covered with dust. The automatic filter cleaning
system will maintain maximum performance and
continue to function. If visual damage to the filter
membrane exists, replace filters. Filters typically last
between six and twelve months depending on use
and care.
TO INSTALL FILTERS
1. Ensure filter seal
15
is in place and is secure.
2. Line up filter threads
and using moderate force, turn filter clockwise until
tight.
NOTE: Use careful to not damage filter material.
3. Place the vacuum head
secure it by closing the lid latches
TO EMPTY DUST TANK (Fig. J)
WARNING: To reduce the risk of injury from
accidental starting, unplug power cord before
emptying the dust tank.
1. Remove the power head assembly of the wet/
dry vac bypulling outward on the lid clips located
on each side of the vac. Lift off the power head
assembly.
2. Dump the tank contents into the proper waste
disposal container.
BLOWING OPERATION
WARNING: To avoid injury to bystanders, keep
them clear of blowing debris.
CAUTION! Wear a dust mask if blowing creates
dust which might be inhaled.
CAUTION! To reduce the risk of hearing loss,
wear ear protectors when using the vac/blower for
extended hours or when using it in a noisy area.
BLOWING FEATURE (Fig. C)
WARNING: To avoid injury to bystanders, keep
them clear of blowing debris.
The vacuum contains a blowing feature. It has the
capability to blow sawdust and other debris. It can be
used to blow dust and debris out of garages or off
patios and driveways. Follow the steps below to use
the vacuum as a blower.
8
16
to vacuum head threads
4
onto the dust tank and
5
.
Advertisement
