Advertisement
Available languages
Available languages
EN
DESCRIPTION (Fig. A)
WARNING: Never modify the power appliance or
any part of it. Damage or personal injury could result.
1
Top handle/cord wrap
2
Power cord
3
On/off switch
4
Vacuum head
Lid latches
5
Dust tank
6
7
Hose
8
Casters
9
Clean Connect
filter
TM
10
Vacuum port
11
Hose strap
12
Disposable dust bag
ASSEMBLY AND ADJUSTMENTS
(Fig. A–C)
WARNING: To reduce the risk of injury, turn
appliance off and disconnect appliance from
power source before installing and removing
accessories, before adjusting or changing set-
ups or when making repairs. An accidental start-up
can cause injury.
WARNING: The fiter
9
while vacuuming, except as described under WET
PICK UP APPLICATIONS under OPERATION.
When vacuuming fine dust, you may also need to
use an disposable dust bag to make emptying the
dust tank easier.
1. Install the disposable dust bag
Fig. B.
NOTE: Be careful not to tear the bag. Place bag
securely onto vacuum port
seal for maximum dust collection performance.
2. Place the vacuum head
secure it by closing the lid latches
3. Insert the end of hose
port
10
and tighten the end of hose to the tank.
OPERATION
INSTRUCTIONS FOR USE (Fig. A, D, E)
WARNING: Always observe the safety
instructions and applicable regulations.
1. Plug the power cord into an appropriate outlet.
2. Turn the on/off switch
3
3. The DEWALT construction dust extractor is fitted
with the DEWALT connection system. It allows a
fast, secure connection between the hose
power tool. The connector
DEWALT compatible tools or through the use of an
adapter (available from local DEWALT supplier). If
you need to Install the adapters, refer to Fig. E.
NOTE: If using an adapter ensure it is firmly
attached to the tool outlet before following the
steps below.
must always be in place
, as shown in
12
10
to provide a tight
4
onto the dust tank and
5
.
7
into clip-in hose vacuum
to the ON position (I).
7
and
13
connects directly to
OPERATING INSTRUCTIONS
CASTER INSTALLATION (Fig. A, F)
1. Invert the dust tank and install the casters to the
bottom of the dust tank and fix them with screws.
2. Return dust tank assembly upright.
REMOVE/CHANGE USED DISPOSABLE
DUST BAG (Fig. A)
WARNING: Appropriate personal protective
equipment like dust mask and gloves should be used
while handling used dust bags.
1. Turn off vacuum and unplug cord from outlet.
2. Unlatch lid latches
5
3. Pull the disposable dust bag
vacuum port
10
.
4. Seal the disposable dust bag
when removing it from the machine.
5. Dispose the disposable dust bag
container according to statutory provisions.
WET PICK UP APPLICATIONS
(Fig. A, G)
WARNING: If foam or liquid escapes from the
machine,switch off immediately.
WARNING: Do not use the machine with this set
up for dust Class L.
The ball float
14
will block air to the motor when
the dust tank is full and the sound of the motor will
change at once. When the motor has a high pitched
sound and air/water flow stops, empty the dust tank.
1. Turn off vacuum and unplug cord from outlet.
2. Unlatch lid latches
5
3. Empty contents of dust
container or drain.
CAUTION! Clean the water level limiting device
regularly and examine it for signs of damage. Refer
to Fig. G.
NOTICE: DO NOT remove ball float
so will cause damage to the vacuum. The ball float
keeps water from entering the motor.
Before using the vacuum for wet pick up:
• Ensure the dust tank is empty and free of excessive
dust.
• Remove the filter
9
.
TO CONVERT BACK TO DRY VACUUM
OPERATION (Fig. A)
1. Empty dust tank, refer to TO EMPTY DUST TANK
instructions.
2. Place dust tank upside down position until dry. DO
NOT use wet dust tank for dry pick up.
3. Place vacuum head
appliance dry.
4. Reinstall filters when vacuum head is dry. Refer to
TO INSTALL FILTERS.
5. When dust tank is dry place the vacuum head
4
onto the dust tank and secure it by closing
the lid latches
.
5
7
and remove vacuum head
12
carefully from
12
opening tightly
12
in appropriate
and remove vacuum head
6
tank into a suitable
14
, doing
4
on a level surface
4
.
4
.
Advertisement
