Additional Features - Whirlpool Cabrio WED6200S Use & Care Manual

Enhanced Touch Up
This cycle is best for touching up clothes that have been left in the
dryer too long. In this cycle, a small amount of water is sprayed
into the dryer drum after several minutes of tumbling with heat.
The dryer will continue to tumble with heat followed by a brief cool
down. The dry time and temperature can be adjusted for this
cycle.
NOTE: Overloading the dryer may not yield the same results.
Steam Preset Cycle Settings
Timed Cycles
Load Type
QUICK REFRESH
Helps to smooth out
wrinkles and reduce odors
from loads consisting of
one to four dry items.
ENHANCED TOUCH UP
Helps to smooth out
wrinkles in loads left in the
dryer for an extended
period.
*Temperature and Time Adjust are selectable only for the
Enhanced Touch Up Cycle.
NOTE: The Enhanced Touch Up cycle has a minimum dry time of
15 minutes and a maximum dry time of 40 minutes. Only the
Medium and High temperature settings can be used for the
Enhanced Touch Up cycle.
Timed Cycles
Use Timed Cycles to select a specific amount of drying time and a
drying temperature. When a Timed Cycle is selected, the
Estimated Time Remaining display shows the actual time
remaining in your cycle. You can change the actual time in the
cycle by pressing the Time Adjust up or down arrows. See
"Changing Cycles, Modifiers, and Options."
NOTE: Timed Cycles may also be used with the dryer rack. See
"Dryer Rack."
Timed Dry
Use this cycle to complete drying if items are still damp after an
Automatic Cycle. Lightweight garments, such as exercise wear,
can be dried using Timed Dry on a low temperature setting.
Timed Preset Cycle Settings
Timed Cycle
Load Type
TIMED DRY
Use if items are still damp
after an automatic cycle.
Heavyweight, bulky items,
bedspreads, and work
clothes
QUICK DRY (on some
models)
Small loads or short
drying time
TOUCH UP (on some
models)
Helps to smooth out
wrinkles for clothes
packed in the suitcase or
left in the dryer too long
Default Default Time
Temperature* (Minutes)*
Medium 15
Medium 20
Default Default Time
Temperature (Minutes)
High 40
Medium 24
Medium 20

Additional Features

Automatic Cycle Modifiers
Use the Dryness Modifier to select dryness levels for the Auto Dry
Cycles. Press DRYNESS until the desired Dryness setting
illuminates.
The preset dryness setting is Normal when an Automatic Cycle is
selected. You can select a different dryness level, depending on
your load, by pressing Dryness and choosing More, Normal, Less,
or Damp. Selecting More, Normal, Less, or Damp automatically
adjusts the dryness level at which the dryer will shut off. Once a
dryness level is set, it cannot be changed without stopping the
cycle.
NOTE: Dryness Level selections cannot be used with the Timed
Cycles.
Timed Cycle Modifiers
Use the Temperature Modifier to select temperatures for the
Timed Cycles. Press TEMP until the desired temperature setting
illuminates.
NOTE: Temperature modifiers cannot be used with the Auto Dry
Cycles.
Air Only
Use the Air Only Modifier for items that require drying without heat
such as rubber, plastic and heat-sensitive fabrics. This table
shows examples of items that can be dried using Air Only.
Type of Load
Foam rubber - pillows, padded bras, stuffed toys
Plastic - Shower curtains, tablecloths
Rubber-backed rugs
Olefin, polypropylene, sheer nylon
*Reset cycle to complete drying, if needed.
When using Air Only
■ Check that coverings are securely stitched.
■ Shake and fluff pillows by hand periodically during the cycle.
■
Dry item completely. Foam rubber pillows are slow to dry.
NOTE: Air Only is not available with Automatic Cycles.
Time*
(Minutes)
20 - 30
20 - 30
40 - 50
10 - 20
7