Table of Contents
Advertisement
(68702
'ON)
QL-L
'Auto Fane
FUZZY LOH CO REC
4
Jomect
Fuzzy CD Recording
If the recording level is too high, distortion will result; On the other hand, if the recording level
is too low, the sound volume will be low. So, itis very important to check the peak level of the
source tracks before recording. Furthermore, itis necessary to check the tracks' overall Jevel. With
the Fuzzy CD Recording feature, if the tracks' overall level is high, the recording level will be set
lower, and, if the tracks' overall level is low, the recording level will be set higher. In this way,
the optimum recording level is set according to the sound inclination of the tracks as well as the
peak level. The conventional peak search function does not take into account the tracks' overall
balance when setting the recording level; therefore, the recording level tended to be low. Fuzzy
CD Recording gives a balanced recording level which matches different kinds of tracks.
I. Load a CD in the tray.
2.
Put a tape in deck B.
3. Select the side to record on, by pressing either the < or > button while pressing the
button on deck B.
4. Press either FUZZY LOGIC CD REC AUTO FADE or DIRECT button.
The tape starts recording 10 seconds before the CD starts, making a 10-second blank
at the beginning of the tape to insure the entire selection is recorded.
AUTO FADE starts recording with Al Edit (page 27) and FADE mode (page 25).
DIRECT starts recording from the first track to the end.
+
When FUZZY LOGIC CD REC (either AUTO FADE or DIRECT) is pressed, the
optimum recording level will be determined by the fuzzy search, then the recording will
start from the first CD track. (Since the fuzzy search will search the entire CD, it will take
a little time.)
*
During the fuzzy search, the track number, number of tracks, playing time, etc., will
change accordingly.
*
If the last recorded track cannot fit on side A, it will be re-recorded with fade-out.
«
Whenthe REVERSE MODE selector is set to either
D or >,
side B recording will start
after a blank portion of !O seconds is made. The recording will continue with the last track
recorded with a fade-out on side A.
+
The last track on side B will end by fading-out.
+
ff the inserted tape has not been rewound, it will be rewound automatically before
recording begins.
To stop recording
Press the l@ button on deck B or the STOP/CLEAR @ button on the CD player.
Note
The tracks can be recorded with a specified sound effect (SEA pattern and Panoramic Surround
modes). Sound effects cannot be changed during recording.
Page 26
Al Edit
Blank
Fade out
a [ets
Te To}
A
7
Remaining time
Blank
Auto Edit
Blank
Remaining time
Remaining time
Blank
PRGM Edit
Remaining tim
Remaining time
Blank
Multi Edit
Blank
Remaining time
to be continued
Page 27
Using CD Edit Mode
The XT-G70RBK
has four CD Edit modes; Al Edit, Auto Edit, Program Edit and Multi-Edit. To
take advantage of these Edit modes, read the following instructions carefully.
What is Al Edit?
This is an editing function which complements the Auto Edit mode (below). You can use it to
maximize the use of the remaining tape length. When the tape comes to its end, the FADE mode
will function automatically. Up to 16 tracks can be edited for one side.
What is Auto Edit?
To prevent the beginning of the track from not being recorded, the last track will be replaced
automatically in accordance with the remaining tape length. The editing will start with the earlier
tracks and the tracks will be selected so they can fit on the tape. No track is selected twice.
However, depending on the remaining time, the same track may be selected twice to fill in the
recording time at the end of the tape. Up to 16 tracks can be edited for one side.
What is PRGM (program) Edit?
Using this mode you can select which CD tracks go on which side of the tape, and in what order,
What is Multi Edit?
Using this mode you can select tracks from several different CDs, The NONSTOP and FADE
NONSTOP modes cannot be used with Multi Edit mode.
Operating procedures
1. Load a CD in the tray.
*
2. Press the EDIT MODE button to select the desired CD Edit mode you want to use.
Each time you press the button the indicator is displayed as follows in the CD display.
ie Ai——> AUTO—*PRGM —> MULTI— =e]
3. Press the TIME button to select the time length.
Each time you press the button, the pre-programmed tape length is shown on the display as
follows.
Reco
54——» 60 "7
90+
80+
74
70
64
If you want touse the Remote, you can set the tape length by using the +10 button and 10 keys.
(Make sure that the TUNER/CD/PANORAMIC SEA selector is set to the CD position.)
ex.
C-30:
+10, +10, 10.
C-46:
+10, +10, +10, +10, 6.
C-74;
+10, +10, +10, +10.....Press the +10 button seven times,
then press 4 button.
This number shows how many times you have pressed the +10 button.
to be continued
WaYO
Advertisement
Table of Contents
