Table of Contents
Advertisement
Speakers
This unit has two pairs of speaker terminals, SPEAKERS A and
SPEAKERS B.
Connecting one speaker system
Connect speakers rated at 4 ohms or more to the SPEAKERS
A terminals.
Connecting two speaker systems
To connect an additional pair of speakers,
use the B ter-
minals. !n this case, each speaker must be rated at 8 ohms or
more.
Connection with speaker cords
1. Connect the left speaker to the [LISPEAKERS terminals and
the right speaker to the [R] SPEAKERS terminals.
2. Be careful that wires do not contact adjacent terminals.
3. Be sure to connect the (+) terminal of the speaker to the
(+) terminal of the unit.
Never short the (+) and (—) terminals.
Erroneous connection of speakers may result in poor imaging
or unnatural sound.
Remove insulation
ST
from lead tip.
Insert the wire and
The wire is
return the lever.
now locked.
Twist wire tightly,
ssf
and solder.
Press the lever.
Speaker lead connection
Setting SPEAKER IMPEDANCE SELECTOR
CAUTION
Speaker impedance selector:
When connecting one pair of speakers to the SPEAKERS A or
B terminals, set the IMPEDANCE SELECTOR according to the
speaker impedance.
42,60—
'Aor B (BELOW 8 Q)
A and B (ANY SPEAKERS)"'
8 2, 16 2 — 'A or B (8 Q OR MORE)"
When
connecting speakers to both SPEAKER A and B ter-
minals, always set the IMPEDANCE SELECTOR to
"A or B (BELOW 8 9), A and B (ANY SPEAKERS)"'.
IMPEDANCE SELECTOR
<0
AorB
AorB
(BELOW 8 Q)|
(8 Q OR MORE)
A and B
(ANY
SPEAKERS)
Notes:
1. During speaker system connection and operation of SPEAKER IM-
PEDANCE SELECTOR, set the POWER switch to OFF.
2. Check that the connected lead wires of the speaker systems do
not contact with other jacks or terminals.
Turntable
The PHONO jacks of the unit can be connected to either type
of turntable: one using MM cartridge or one using MC car-
tridge.
Your
stereo turntable has RCA
pin-plug cords that is ter-
minated with phono plugs. Plug the left channel plug into the
and the right channel plug into the ([R] PHONO jacks.
If the turntable has a ground wire, connect it to the unit's
GND terminal to avoid hum.
CD/AUX
Ground
Tape decks
Playback
;
Record
Second tape deck
VIDEO (VIDEO/AUDIO) jacks
Two video recorders can be connected to the VIDEO A and
VIDEO B jacks.
Connect the unit's VIDEO PLAY jack to the video recorder's
video output terminal, the VIDEO REC jack to the video input
terminal, the AUDIO PLAY
jack to the left audio output .
terminal, AUDIO
PLAY
[R] jack to the right audio output
terminal, AUDIO REC [L] jack to the left audio input terminal,
and the AUDIO REC [R] jack to the right audio input terminal.
(Video recorder with monaural audio should be connected to
one of the VIDEO A jacks. After connecting it to the {£] or [R]
AUDIO jack of the VIDEO A jacks, set the MONO/STEREO
switch to ''MONO''.)
MONO/STEREO switch
This switch affects only the VIDEO A jacks. Set the switch
according to the stereo or monaural audio output mode of the
video recorder connected to the VIDEO A jacks.
MONITOR OUT jacks
SYNCHRO CONTROL terminal
When
the KD-75F
(KD-74F)/KD-65F
(KD-64F)
(turntable),
KX-95WI/KX-75/R
(KX-74R)
(tape
deck)
or
DP-850
(DP-840)
(CD
player)
are
used
in connection
with
the
receiver, they can:be operated from the remote control unit of
the receiver when their synchro terminals are connected to
the SYNCHRO
CONTROL
terminals.
(Ordinary audio cable
connections
are
also
required.)
For
details,
refer to the
operating instructions for the remote control unit on page 12.
AM antennas
AM loop antenna
KR-V125R/KR-V75R (U) §
Advertisement
Table of Contents
