Harman Kardon HK 3470 Owner's Manual page 18

Operation
Programming the Remote Buttons Is a
Simple Procedure
Step 1: Placethe HK 3470 remote controland
the remotecontrol for the otherdevice
(eg,r
compactdiscplayer)so that their inflared
transmitterwindowsface eachother at a
distanceof about one-halfinch
Step 2: Simultaneously pressthe Learn button
and the Source Selector (_ that corre-
spondsto the devicewhose codesyou are
trying to program(eg,, pressthe CDbutton
along with the Learnbutton).TheLED
Indicator @ will blink onceand remainlit
Step 3: Pressand releasethe button on the
HK3470 remotethat you wish to program
Makesure that it is one of the program-
mable buttonslisted in the tableon page
17,TheLED Indicator @ will blink once
and remainlit
Step 4: Pressand hold the button on the other
device'sremotewhose codeyou wish to
programinto the HK 3470 remote until the
LED Indicator @ blinksthreetimes and
remainslit, then releasethe button on the
other remote
If the LED Indicator @ flickersfor five sec-
onds insteadof blinking three timesand
remaininglit, the learningoperationwasunsuc-
cessful, f ly the procedureagain,startingflom
Step2, makingsurethat the transmitterwin-
dows of the two remotesface eachother,and
that the buttonyou aretrying to programon
the HK 3470 remoteis listedin the table on
page 17
Step 5: Toprogramadditionalbuttons,repeat
Steps2 through 4
Step 6: To exitthe learningmode,either press
the Learn button_ once,or wait 20 sec-
ondsfor the remoteto automaticallyreturn
to normaloperation,
Resetting One Key to Default Setting
When a new codeis programmedinto the
remote,it overwritesthe previouscodefor that
button on that page. However, s houldyou
makea mistake,it is possibleto resetany but-
ton to its factory default using the following
procedure:
Step 1: Enterthe learning modeby simultane-
ouslypressingany of the Device buttons
and the Learn button
Step 2: Pressand releasethe particulardevice
button for the pagecontainingthe keyyou
wish to reset TheLED Indicator _ will
blink onceand remainon
Step 3: Usethe Numeric Keys_ to enter
the numbers"777", The LEDIndicator
will blink for eachentry,
Step 4: Pressand releasethe button that you
wish to reset TheLED Indicator @ will
blink threetimes to indicatethat the button
has beenresetto the factory default code,
Step 5: Youmay repeatStep4 to resetthe
codesfor otherkeys,If you wish to resetthe
codesfor an entire devicepage,seebelow,
Step 6: To exitthe learningmode,either press
the Learn button_ once,or wait 20 sec-
ondsfor the remoteto automaticallyreturn
to normaloperation,
Resetting an Entire Device Page
If you wish to reset all of the codesfor a partic-
ular device,you need not individuallyreset
everybutton on that pageof the remote This is
the procedurefor resettingthe codeson a par-
ticular page
Step 1: Enterthe learning modeby simultane-
ouslypressingany of the Device buttons
and the Learn button
Step 2: Pressand releasethe particulardevice
button for the pageyou wish to reset,The
LED Indicator @ will blink onceand
remainon
Step 3: Usethe Numeric Keys _ to enter
the numbers"888", 1-he LEDIndicator
will blink for eachentry,
Step 4: TheLED Indicator @ will remainon
for onesecond,and then blink threetimes to
indicatethat it hasresetthe group of keys
for the selecteddevicepage Thatdevice
page will now operatethe factory default set
of codes,
Resetting the Entire Remote
It is alsopossibleto completelyresetall of the
programmedcodesin the remoteto the factory
default settings Usethe following procedure:
Step 1: Enterthe learning modeby simultane-
ouslypressingany of the Device buttons
(_ and the Learn button
Step 2: Pressand releaseany device button
other than PHONO, AM or FM.The LED
Indicator @ will blink onceandremainon
Step 3: Usethe Numeric Keys_ to enter
the numbers"999", TheLEDIndicator
will blink for eachentry,
Step 4: TheLED Indicator @ will remainon
for fiveseconds, a nd then blink threetimes
to indicatethat it hasresetall of the keyson
the remote,The entireremote will now oper-
ate the factory default set of codes,
18 OPERATION I