Table of Contents
Advertisement
HCD-SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30/HCDSHAKEX70
PANEL TEST MODE
This mode is used to check the buttons, knobs, screen display
panel and LEDs.
Procedure:
1. Press [
] to turn on the system.
1
2. Press [] button and [
ously for 3 seconds.
3. All LEDs and segments in screen display panel are lighted up.
This is the display check mode.
Press [ENTER] button repeatedly to toggle different display
mode as below.
Segments on screen display panel:
All On -- > 1st Group On -- > 2nd Group On -- > All On -- > All
Off
Single color LEDs:
All On -- > 1st Group On -- > 2nd Group On -- > All On -- > All
Off
Multi Color LEDs:
White -- > Red -- > Green -- > Blue -- > Off
4. Press [
- ] button, the button and knob check mode is
activated.
5. In the button and knob check mode, the screen display
panel displays "K 0 E0V0".
Each time a button is pressed, "K" value increases.
However, once a button has been pressed, it is no longer
taken into account. After all the buttons have been
pressed, "K" value will toggle between "OK" and "K26".
"E" value increases in the manner of 0, 1, 2, 3 ... if
[MIC/GUITAR LEVEL] knob is turned clockwise, or it
decreases in the manner of 0, 9, 8, 7 ... if [MIC/GUITAR
LEVEL] knob is turned counterclockwise.
"V" value increases in the manner of 0, 1, 2, 3 ... if
[VOLUME/DJ CONTROL] knob is turned clockwise, or
it decreases in the manner of 0, 9, 8, 7 ... if [VOLUME/
DJ CONTROL] knob is turned counterclockwise.
6. To release from this mode, press the buttons in the same
manner as step 2, or disconnect the power cord.
VERSION DISPLAY MODE
This mode is used to check the software version.
Procedure:
1. Press [
] button to turn on the system.
1
2. Press [
TUNING – .] button and [LIGHT MODE] but-
ton simultaneously for 3 seconds.
The SC software version and CD/DVD software appear on the
screen display panel.
After that, it returns to the default display.
MODEL AND DESTINATION DISPLAY MODE
This mode is used to check the model and destination of the set.
Procedure:
1. Press [
] button to turn on the system.
1
2. Press [] button and [
ously for 3 seconds.
All segments in screen display panel are lighted up.
3. Press [
+ ] button. Model information appears on the
screen display panel.
4. Press [
+ ] button again. Destination information appears
on the screen display panel.
5. Press [] button and [
ously for 3 seconds to exit.
SECTION 3
TEST MODE
TUNING – .] button simultane-
TUNING – .] button simultane-
TUNING – .] button simultane-
USER RESET
The user reset clears all data including preset data stored in the data
fl ash to initial conditions exclude history mode data.
Procedure:
1. Press [
] button to turn on the system.
1
2. Press [DJ OFF] button and [
taneously for 3 seconds.
3. "RESET" appears on the screen display panel. After that, the
screen display panel becomes blank for a while, and the system
goes to demo mode.
COLD RESET
This mode is used to reset all the user settings to factory setting.
Execute this mode when returning the unit to the customer.
Procedure:
1. Press [
] button to turn on the system.
1
2. Press [] button and [
ously for 3 seconds.
3. "COLD RESET" appears on the screen display panel. After
that, "SONY DEMO" appears on the screen display panel.
The system automatically turn on and off once. Please be sure
that the system stay at demo mode fi nally before switch off the
power supply.
DISC TRAY LOCK
When the disc tray does not open and "LOCKED" appears on the
screen display panel, disc tray lock mode has been activated by the
shop front.
To release from Disc Tray Lock Mode
1. Press [
] button to turn on the system.
1
2. Press [FUNCTION] button repeatedly to select DVD/CD
function.
3. Press [ENTER] button and [VOCAL FADER] button
simultaneously and hold down until "UNLOCKED" displayed
on the screen display panel.
BLUETOOTH PAIRING HISTORY CLEAR
This mode is used to delete the Bluetooth pairing history on the
system.
Procedure:
1. Press [
] button to turn on the system.
1
2. Press [FUNCTION] button repeatedly to turn the Bluetooth
function.
3. Press [ENTER] button and [LIGHT MODE] button
simultaneously for 3 seconds.
4. The message "BT HISTORY" → "CLEAR" appears on the
screen display panel. The pairing history has been deleted.
SHOP FRONT DEMO
The playback started automatically and the " * DEMO * " appears
on the screen display panel.
This is the Shop Front Demo mode which is activated by the shop
front.
To release from Shop Front Demo Mode
1. Press [] button and [SOUND FIELD] button simultaneously for
5 seconds.
TUNING + >] button simul-
TUNING + >] button simultane-
21
SYS SET
Advertisement
Table of Contents
