Advertisement
Quick Links
Advertisement
Related Manuals for NCR 7360-K502
Summary of Contents for NCR 7360-K502
- Page 1 Kit Instructions Input Belt Adapter 7360-K502 Issue A...
- Page 2 NCR, therefore, reserves the right to change specifications without prior notice. All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, photographs are of equipment prototypes. Software screen images are representative, and in some cases, may not match a customer’s installed software exactly.
- Page 3 Revision Record Issue Date Remarks Mar 2022 First Issue...
- Page 4 Input Belt Adapter This publication provides the following procedures for installing the Input Belt Adapter on the NCR FastLane SelfServ™ Checkout (7360) unit. The Input Belt Adapter is used for the 7344 Input Belt assembly that is removed from either an NCR SelNCR SelfServ™...
- Page 5 Input Belt Adapter Part Number Description 009-0007087 Serrated Nut - Self Locking (M4, 4.2) (14 pcs) 009-0006599 Screw Hex M6 X 12 MC COMB (12 pcs) 006-8611464 Washer -Flat, 1/4" Size,5/16" ID 3/4" OD, 1/16" Thk (4 pcs) 006-8624713 Washer -Flat, 1/4" Size, 9/32" ID, 1" OD (3 pcs) 497-0423108 Instructions Kit (Reference Sheet) * Items marked with an asterisk are not called out on the image.
- Page 6 Input Belt Adapter Installing the Input Belt Adapter To install the Input Belt Adapter, follow these steps: Note: This procedure shows images of a Right-Hand unit for illustration purposes only. The steps are the same for a Left-Hand unit. 1. If necessary, remove the cable plate from the side of the core (next to scanner bucket) and rotate it so that cable access hole is exposed.
- Page 7 Remove the Conveyor Belt from the Input Belt assembly. For more information, refer to Removing the Conveyor Belt assembly on page 30. b. Remove the Input Belt assembly from either the NCR SelfServ™ Checkout (7350) or NCR FastLane SelfServ™ Checkout (7358) R6L Plus. For more information, refer to Removing the Input Belt assembly on page 34.
- Page 8 Input Belt Adapter 3. Move the Input Belt assembly near the SelfServ Checkout Core Cabinet with the Input Belt Adapter. Note: Do not join the Input Belt assembly to the Input Belt Adapter because the cable access holes do not align. 4.
- Page 9 Input Belt Adapter 5. Slightly lift the Input Belt assembly to align with the alignment screws and then slide the assembly down onto the screws. 6. Secure the Input Belt assembly to the Core Cabinet using four (4) screws, as shown in the image below.
- Page 10 Input Belt Adapter 7. Remove the screws on the Input Belt Mount one-by-one and add a washer to each screw. 8. Route the Input Belt cables in the SelfServ Checkout Core Cabinet. For more information, refer to Routing Input Belt Cables on page 12.
- Page 11 Input Belt Adapter 11. Install a teardrop-shaped Gasket to prevent crumbs from filling up the tapered area around the perimeter of the Top Plate. 12. Do the following: a. Turn on the Input Belt power. For more information, refer to Turning On the Input Belt on page 38.
- Page 12 Input Belt Adapter Routing Input Belt Cables To route the Input Belt cables through the SelfServ Checkout Core Cabinet, follow these steps: 1. Install the Input Belt to the SelfServ Checkout. For more information, refer to Installing the Input Belt assembly on page 7.
- Page 13 Input Belt Adapter Routing Input Belt DC Power Cable in Left-Hand units To route the Input Belt cables through the SelfServ Checkout Core Cabinetin a unit with Left-hand (LH) orientation, follow these steps: 1. Install the Input Belt to the SelfServ Checkout. For more information, refer to Installing the Input Belt assembly on page 7.
- Page 14 Input Belt Adapter Routing Input Belt DC Power cable in Right-Hand units To route the Input Belt DC Power cable through the SelfServ Checkout Core Cabinet in a unit with Right-hand (RH) orientation, follow these steps: 1. Install the Input Belt to the SelfServ Checkout. For more information, refer to Installing the Input Belt assembly on page 7.
- Page 15 Input Belt Adapter Routing the Input Belt AC Power Cable in Left-Hand units To route the Input Belt AC power cable through the SelfServ Checkout Core Cabinet and into the Power Strip in a unit with Left-hand (LH) orientation, follow these steps: 1.
- Page 16 Input Belt Adapter 4. Do the following: a. From the back of the SelfServ Checkout unit, route the Input Belt AC Power cable into the Bagwell through the Side Cable Access hole and then fasten the cable on a bridge lance. b.
- Page 17 Input Belt Adapter Routing the Input Belt AC Power Cable in Right-Hand units To route the Input Belt AC power cable through the SelfServ Checkout Core Cabinet and into the Power Strip in a unit with Right-hand (RH) orientation, follow these steps: 1.
- Page 18 Input Belt Adapter 4. Do the following: a. From the back of the SelfServ Checkout unit, route the Input Belt AC Power cable into the Bagwell through the Side Cable Access hole and then fasten the cable on a bridge lance. b.
- Page 19 Input Belt Adapter Routing Input Belt AC Junction Box cable through Left-Hand units To route the AC Junction Box cable from the Input Belt frame through a unit with Left- hand (LH) orientation and into the store’s power pole, follow these steps: 1.
- Page 20 Input Belt Adapter 4. Do the following: a. From the back of the SelfServ Checkout unit, route the AC Junction Box cable into the Bagwell through the Side Cable Access hole and then fasten the cable on a bridge lance. b. From the Side Access hole, route the cable out of the SelfServ Checkout unit through the Cable Exit hole at the base of the Bagwell, as shown in the image below.
- Page 21 Input Belt Adapter Routing Input Belt AC Junction Box cable through Right-Hand units To route the AC Junction Box cable from the Input Belt frame through a unit with Right- hand (RH) orientation and into the store’s power pole, follow these steps: 1.
- Page 22 Input Belt Adapter 4. From the Side Cable Access hole in the Bagwell, do the following: a. Fasten the cable on a bridge lance. b. Route the cable out of the SelfServ Checkout unit through the Cable Exit hole at the base of the Bagwell, as shown in the image below.
- Page 23 Input Belt Adapter Adjusting the Input Belt Tracking Turn on and then run the Input Belt to determine if tracking adjustments are needed. If tracking adjustments are needed, follow these steps: 1. Remove four (4) screws securing the Rear Cover to the Input Belt frame.
- Page 24 Input Belt Adapter 2. Remove two (2) hex bolts securing the Input Belt assembly to the Scale Pods.
- Page 25 Input Belt Adapter 3. Do the following: a. Stand at the end of the Input Belt. b. Grasp the Converyor Belt assembly, lift and then slide it forward to disengage the assembly from the PEM studs. Note: Hold the motor power cable so that it does not pinch. c.
- Page 26 Input Belt Adapter 4. On the Adjustment Bracket, loosen the Jam nut. Note: The Jam nut is shown on the image below. 5. Using a wrench, adjust the Alignment nut as needed to change belt tracking and tension. Moving the motor bracket toward the rear will increase the belt’s tension and cause the belt to track to the opposite side.
- Page 27 Input Belt Adapter 8. Do the following: a. Lift and then lower Input Belt assembly into the Input Belt frame to engage with the PEM studs. Note: Ensure that the motor power cable is not pinched. b. Slide the Input Belt assembly forward until it securely stops.
- Page 28 Input Belt Adapter 9. Secure the Input Belt assembly to the Scale Pods using two (2) hex bolts. 10. Secure the Rear Cover to the Input Belt frame using four (4) screws.
- Page 29 Input Belt Adapter Leveling the Input Belt When attaching an Input Belt to the NCR FastLane SelfServ™ Checkout unit, ensure that the top surfaces of the Input Belt module switch plate and the SelfServ Checkout unit are flush and level. To level the Input Belt, follow these steps: 1.
- Page 30 Input Belt Adapter Removing the Conveyor Belt assembly To remove the Conveyor Belt assembly from a NCR SelfServ™ Checkout (7350) or NCR FastLane SelfServ™ Checkout (7358) R6L Plus unit, follow these steps: Note: This procedure shows theNCR FastLane SelfServ™ Checkout (7358) R6L Plus for illustration purpose only.
- Page 31 Input Belt Adapter 4. Do the following: a. Remove two (2) hex bolts securing the Input Belt Conveyor assembly to the Scale Pods. b. Remove the four (4) hex bolts (two on each side) securing the Conveyor Belt assembly to the Input Belt frame. These bolts are located underneath the Input Belt frame, as shown in the image below.
- Page 32 Input Belt Adapter 5. Do the following: a. Stand at the end of the Input Belt. b. Grasp the Input Belt assembly, lift and then slide it forward to disengage the assembly from the PEM studs. Note: Hold the motor power cable so that it does not pinch.
- Page 33 Input Belt Adapter c. Rest the rear of the Input Belt Conveyor assembly on the edge of the Input Belt frame as shown in the image below. Note: Ensure not to pinch the motor cable. Note: It is recommended that you rest the belt assembly on a couple of supports on top of the cabinet to make it easier to service.
- Page 34 Input Belt Adapter Removing the Input Belt assembly To remove the Input Belt assembly from a NCR SelfServ™ Checkout (7350) or NCR FastLane SelfServ™ Checkout (7358) R6L Plus unit, follow these steps: Note: This procedure shows theNCR FastLane SelfServ™ Checkout (7358) R6L Plus for illustration purpose only.
- Page 35 Input Belt Adapter NCR FastLane SelfServ™ Checkout (7358) R6L Plus 3. Remove two (2) screws from inside the Input Belt frame, as shown in the image below.
- Page 36 Input Belt Adapter 4. Remove three (3) screws from the Input Belt Mount, as shown in the image below. Caution: Ensure that someone is holding the Input Belt to avoid dropping it.
- Page 37 Input Belt Adapter Turning Off the Input Belt Turning off the Input Belt deactivates the motor and the belt cannot detect the presence of an item. To turn off the Input Belt, verify that the Power Switch is turned off.
- Page 38 Input Belt Adapter Turning On the Input Belt Turning on the Input Belt activates the motor and the belt automatically detects the presence of an item. To turn on the Input Belt, verify that the Power Switch turned is on.