Advertisement
Quick Links
Advertisement
Related Manuals for NCR 7707-K125
Summary of Contents for NCR 7707-K125
- Page 1 Kit Instructions USB-to-Serial Adapter Cable (Sabrent) 7707-K125 Issue A...
- Page 2 NCR, therefore, reserves the right to change specifications without prior notice. All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR office for information that is applicable and current.
-
Page 3: Revision Record
Revision Record Issue Date Remarks Apr 2020 First Issue... -
Page 4: Kit Contents
The USB-to-Serial Adapter Cable (Sabrent) converts data sent from currency devices to the Terminal Display through its USB port. Using this cable can help improve communication between the devices. This publication provides procedures for routing the USB-to-Serial Adapter Cable in the NCR SelfServ™ Checkout (7707) unit. Kit Contents Part Number... -
Page 5: Installation Procedures
USB-to-Serial Adapter Cable (Sabrent) Installation Procedures Installing the USB-to-Serial Adapter Cable involves the following procedures: • Routing USB-to-Serial Adapter Cable on the facing page. • Installing USB-to-Serial Adapter Driver on page 11. - Page 6 Routing USB-to-Serial Adapter Cable To route the USB-to-Serial Adapter Cable, follow these steps: 1. Shut down the NCR SelfServ™ Checkout (7707) R6-Japan software and hardware systems. 2. Detach the back panel from the Tower Frame by removing two (2) screws.
- Page 7 USB-to-Serial Adapter Cable (Sabrent) 3. Detach the back panel of the Lower Core (Cabinet) Module by removing six (6) screws to access the devices and cable routing.
- Page 8 USB-to-Serial Adapter Cable (Sabrent) 4. Disconnect the currency device connector from the KIO board by doing the following: a. Access the KIO Board. b. Disconnect the RS232 DB9 connector from the COM1 port of the KIO Board, as shown in the image below. Note: For units where the currency device cable is connected to the RJ50 serial adapter of the Terminal Display, disconnect the cable as shown in the image below.
- Page 9 USB-to-Serial Adapter Cable (Sabrent) 6. Unlock the Tower frame from the back using a key. 7. Raise the Terminal Display.
- Page 10 USB-to-Serial Adapter Cable (Sabrent) 8. Detach the cable guide by removing one (1) screw, as shown in the image below. 9. Connect the USB-to-Serial adapter cable to the USB Port B of the Terminal Display. Warning: Ensure that the system is turned off before disconnecting or connecting cables to avoid damaging the internal chip of the Terminal Display and making the adapter unusable.
- Page 11 USB-to-Serial Adapter Cable (Sabrent) 11. Attach the cable guide using one (1) screw. 12. Connect the currency device cable to the USB-to-Serial adapter cable and then secure the connection by tightening the two (2) screws.
- Page 12 USB-to-Serial Adapter Cable (Sabrent) 13. Route the excess cable length on the rear left side of the lower cabinet by doing the following: a. Create a large loop. b. Insert the excess cable through the P-loop, as shown in the image below. 14.
- Page 13 3-10 USB-to-Serial Adapter Cable (Sabrent) • Attach the lower back panel to the lower cabinet using six (6) screws. 15. Lower the Terminal Display and then lock the Tower frame using a key.
- Page 14 The driver will not successfully install if these cables are not connected. Note: The unit must have an internet connection to download the driver file/s. 1. Access the driver from this link: \\susdlg890.pioneers.ncr.com\platform\ADD Package\Released\Hotfix\Kiosk\HF1803_Prolific_Driver_Update_v1.0 Note: For more information, refer to HF1803_Prolific_Driver_Update_v1.0 - Release Notes.
- Page 15 3-12 USB-to-Serial Adapter Cable (Sabrent) 5. Once the installation process is completed, do the following: a. Go to C:\scot\config\ b. Update the with the following data below: CADD.001 [7707.SemiSelfJapan] SerialPort1=CashChanger.Glory_Recycler_380 IOBoxPort1=CashChanger.Glory_Recycler_380 IOBoxPort2=MSR.Sankyo_MCRW ProlificPort1=CashChanger.Glory_Recycler_380 c. Go to C:\scot\logs d. Delete CADDRuntime.dat 6.
- Page 16 Exercise the recycler devices using the Profile Manager Lite (PML) tool test utilities and verify that the devices are functioning as expected. For instructions on how to use the PML tool, refer to the NCR FastLane SelfServ™ Checkout Profile Manager Lite User Guide (B005-0000-2279).