Functions - Crosley CR79 Instruction Manual

Basic Operation
Powering Up Your Crosley
Your new Crosley is equipped with a POWER /
STANDBY button. Press the POWER / STANDBY
button on either the front of the unit or on your remote
control. The Standby light will turn from red to green.
When turned off, the standby light will turn red.
During standby mode, all presets will remain
programmed in your unit.

Functions

Electronic Volume Control
1
Press the "VOL+" button to increase the volume.
The volume level will be shown in the LCD
display.
Electronic volume control display
Note: Volume range for this units start at level
0 and end at level 40.
2
Press the "VOL-" button to decrease the volume.
3
Press and hold either the "VOL+" or the
"VOL-" button to continuously increase or
decrease the volume. The volume will continue
to increase or decrease until the button is
released.
4
Press the "MUTE" button to set the volume to
0.
Press the "MUTE" button again to return to the
previous volume level.
7
Functions (cont.)
Function Select
1
Press the "TUNER/BAND" button to enable the
AM/ FM tuning function. When in TUNER mode,
the LCD will display the band (AM/FM), and the
station frequency.
Receiving tuning frequency display
2
Press the "CD" button to set to CD mode. When
first set to CD mode, the display will search for
CD and track information.
After reading display
CD TOC reading display
3
Press the "PHONO" button to set to PHONO
mode. When in PHONO mode, the display will
read "PHONO".
PHONO display
4
Press the "TAPE" button to set to CASSETTE
mode. The display will read "COUNTER" when
in cassette mode.
TAPE mode display
Equalizer
1
This unit has a built in equalizer. The equalizer
fine tunes the sound according to the type of
music you like. Pressing the EQ button results
in the following changes:
FLAT ROCK Jazz
CLASSIC POP
Equalizer "ROCK"
Load Preset Channel
Load up and down correspond to "PS+" and "PS-"
key, respectively.
A
Press "PS+" or "PS-" to recall preset channel
Notes: 1) the current display frequency will not be
kept during above operation.
Preset channel_2
In FM band
loaded
Preset "PS+"
to target preset
channel
Save Preset
Channel number select up or down correspond to
"PS+" and "PS-" key, respectively.
a) In TUNER mode, choose a station that you want
to save. Press "PROG" to enter programming
mode.(--) will flash.
b) Press "PS+" or "PS-" to desired preset number
(e.g. channel-10).
c) Press "PROG" to save that station.
d) Repeat above procedure.
Notes: 1) The original preset of channel-2 will not
be changed during above operation.
In FM band with preset channel In FM band without preset channel
enter to PRESET press "PROG"
SETTING mode
press "PROG"
press "PS+/PS-"
Channel number
to a desired
end of prest
selection channel number
press
"PROG"
Radio
Mono/Stereo
A
Press "MO/ST" to toggle the type of FM signal.
Notes: 1. Only for FM band
2. If stereo signal is too weak, 'STEREO'
icon will not appear. Press this key
change to Mono mode. The reception
may be improved.
In FM band
(Current mode
=Stereo)
Change to
press "MO/ST"
MONO mode
press "MO/ST"
Signal
A high-pitched noise called BEAT is sometime heard
during reception of radio broadcast.
A
In FM band
Press "SIGNAL"
until find a best
quality of signal.
press"Signal"
choose 1st
method
press"Signal"
choose 2nd
method
choose best sound
quality after 3sec
waiting
16