Viking Professional VMOS200 Installation Instructions
Professional series microwave built-in trim kit
Hide thumbs
Also See for Professional VMOS200:
- Service manual (48 pages) ,
- Reference manual (8 pages) ,
- Installation manual (4 pages)
Advertisement
Quick Links
INSTALLATION
INSTRUCTIONS
PROFESSIONAL SERIES
MICROWAVE BUILT-IN TRIM KIT
Retain for Future Reference
IMPORTANT - PLEASE READ AND FOLLOW
• Before beginning, please read these instructions completely and carefully.
• Be sure to DISCONNECT THE PLUG of the microwave oven from the electrical outlet before installing the built-in trim kit.
Remove the turntable from the oven cavity.
• Because the kit includes metal parts, caution should be used in handling and installation to avoid the possibility of injury.
• Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.
• Please observe all local and national codes and ordinances.
• The installer should leave these instructions with the consumer who should retain for local inspector's use and for future
reference.
THIS BUILT-IN KIT IS DESIGNED FOR USE ONLY WITH VIKING MICROWAVE OVENS SPECIFYING BUILT-IN KIT
VMTK270/271, VMTK300/301, OR VMTK360/361 ON THE RATING LABEL ON THE LEFT SIDE WALL OF THE OVEN
CAVITY.
IF YOUR LOWER CONVENTIONAL OVEN IS NOT LISTED IN THE USE AND CARE MANUAL OF THE MICROWAVE
OVEN, THEN DO NOT INSTALL THE MICROWAVE OVEN ABOVE IT OR IN ANY AREA WHERE HEAT AND STEAM
ARE GENERATED; FOR EXAMPLE, NEXT TO OR ABOVE A CONVENTIONAL RANGE.
PARTS INCLUDED IN THE VMTK KIT
1) Front Frame Assembly
QTY 1
2) Bottom Duct Assembly
QTY 1
Greenwood, Mississippi 38930 USA
3) Screw A (1-3/16" length)
QTY 2
VIKING RANGE CORPORATION
111 Front Street
(662) 455-1200
4) Screw B (1 3/4" length)
QTY 4
Advertisement
Related Manuals for Viking Professional VMOS200
Summary of Contents for Viking Professional VMOS200
- Page 1 IF YOUR LOWER CONVENTIONAL OVEN IS NOT LISTED IN THE USE AND CARE MANUAL OF THE MICROWAVE OVEN, THEN DO NOT INSTALL THE MICROWAVE OVEN ABOVE IT OR IN ANY AREA WHERE HEAT AND STEAM ARE GENERATED; FOR EXAMPLE, NEXT TO OR ABOVE A CONVENTIONAL RANGE.
- Page 2 BASIC SPECIFICATIONS Microwave Oven Overall Width 4” Overall Height from 13-3/8” Bottom Overall Depth from 19-1/4” Rear Oven Interior Width Height Depth Overall Cutout Width Cutout Height Cutout Depth Electrical 10VAC/60 Hz Requirements Max. Amp Usage 1.5 KW Approx. Shipping Wt. 46 lbs. VMOS00 VMTK70/71 (60.9 cm) 6-1/” (67.3 cm) (33.9 cm) 18-1/4” (46.3 cm) (48.9 cm) 17-3/8” (44.1 cm) 10-1/” (6.6 cm) 18-5/8” (47.3 cm) .0 cu. ft.
-
Page 3: Cabinet Or Wall Cutout
CABINET OR WALL CUTOUT Cutout Dimensions Height (A) Minimum Maximum Width (B) Minimum Maximum Depth (C) Minimum ELECTRICAL OUTLET LOCATION Outlet should NOT be in the shaded area as indicated on Illustration 1. NOTE 1: If the Depth (C) dimension is greater than 1" (53.3 cm), the outlet location may be in any area on the rear wall. NOTE 2: The floor of the opening should be constructed of plywood strong enough to support the weight of the oven and floor load (approximately 100 pounds). The floor should be level for proper operation of the oven. Be sure to check the local building code as it may require that the opening be enclosed with side, ceiling and rear partition. The proper functioning of the oven does not require the enclosure. BOTTOM DUCT ASSEMBLY 1. Place the Bottom duct in the opening. When the Bottom Duct Assembly is in the opening correctly, the flanges will be tightly against the lower edge of the opening. -
Page 4: Over Oven Installation
FRAME INSTALLATION Position the FRAME ASSEMBLY to be square with the oven. Carefully place the FRAME ASSEMBLY on the oven. Check that it is level and then secure with two SCREWS B. See Illustration 5. Secure the bottom portion of the FRAME ASSEMBLY with the two remaining SCREWS B. OVER OVEN INSTALLATION See Illustration 6. 111 Front Street • Greenwood, Mississippi (MS) 38930 USA • (66) 455-100 For more product information, call 1-888-VIKING1 (845-4641), or visit our web site at http://www.vikingrange.com F0196C TINSEB453MRR0 Illustration 5 SCREW B SCREW B Illustration 6 2"...