Step 4: Setting Up The Vcr With The Auto Set Up Function; Step 5: Selecting The Tv System "Reeesseecveneceeeseeseenesssecneeneasecenesees - Sony SLV-SE220 Service Manual

SEE SSS ee ee ee
Step 4 : Setting up the VCR with the Auto
Set Up function
Before using the VCR for the first time, set up the VCR using the Auto Set Up
function. With this function, you can set the language for the on-screen display, TV
channels, guide channels for the Show View system*, and VCR clock* automatically.
1 Tum on your TY and set it to the video channel.
If your TV does not have a Scart (EURO-AV) connector, tune the
TV to channel 32 (the initial RF channel for this VCR). Refer to
your TV manual for TV tuning instructions. If the picture does not
appear clearly, see "To change the RF channel" on page 22.
2 Connect the mains lead to the
mains.
The VCR automatically turns on,
and the language abbreviations
appear on the TV screen.
— 13 1
The abbreviations of the ser (Oe exit -wenu
languages are as follows:
Abbreviation
3 CED, Press /4/4=/= 10 select the language abbreviation trom the table
t(( =) in step 2, then press OK.
The message for the Auto Set Up function appears.
ear
20 | Setting up the VCR with the Auto Set Up function
To cancel the Auto Set Up function
Press MENU.
To change the RF channel
If the picture does not appear clearly on the TV, change the RF channel on
the VCR and TV. Select INSTALLATION from the menu, then press 4/4
to hightight VCR OUTPUT CH and press >. Select the RF channel by
pressing the & § buttons. Then, tune the TV to the new RF channel so that
aclear pteture appears.
Tip
+ (you want to change the language for the on-screen display from the one preset in
the Auto Set Up function, see page 27.
Notes
¢ Whenever you operate the Auto Set Up function, some of the settings
{Show View * timer. ete) will be reset. If this happens. you have to set them again.
Auto preset starts automateally only when you plug mn the mains Jead for the first
time after you purchase the VCR
After using the Auto Set Up function. the language abbreviations do not appear
automatically when you connect the mains lead again. If you want to use the Auto
Set Up tunchon agam. press MENU, then press #4 4== to highlight
INSTAL LATION and press OK. Press /# to highlight AUTO SET UP, then
Tepeat al} procedures tram step 4.
Auto preset can be pertormed by pressing Ml (stop) on the VCR continuously for
5 seconds or more with no tape inserted.
not available on SLV-SE620N and SE420K.
22 | Setting up the VCR with the Auto Set Up function
Press OK.
The COUNTRY SELECTION 2
menu* appears. $
a
wo
OTHERS g
The abbreviations of the ser OR ext menu] iit
countries are as follows:
Al 1 | Country
Austria
Belgium
Denmark
Finland.
t
Germany
Netherlands
ltaly
Norway
Portugal
5 AS For SLV-SE820N, SE720N and
SX720N
Press #:$ = = to select the AUTO BET UP
abbreviation of your country from PLEASE WAIT
the table in step 4. then press OK. ab
Hf your country does not appear, (@eenenses-------------{
select OTHERS,
: ? EXIT: MENU
The VCR starts searching for all of
the reeenvable channels und presets
them (in the appropriate order for your local area).
Ifyou want to change the order of the channels or disable unwanted
Programme posthons, see "Chang mg disabling programme
Posibons" on page 34
Atter the scarch or download is complete, the current time appears
Jor any stahons that transmit a time signal. If the time does not
appear. sect thy clock manually. See "Setting the clock" on page 24.
For SLV-SE620N and SE420K
The clock sctng menu appears. See "Setting the clock" on
page 24
CONTINUE won
Setting up the VCR with the Auto Set Up function | 24
SSS SL a i a EE
Step 5 : Selecting the TV system
You must select the appropriate EN sv stem for your area.
payers Bum en
Before you start
e tumon the VOR andi TN
© Setthe TY tothe ve fan
© Refer te "inden te pus Wed comtrors fet button locations.
1 wey PES MENT thon tess # t+
OQ 2 tee boot ote INSTALL ATION fr
seth ps OO
AUTO: GBT UP.
MANUAL SET UP
SMARTLINK
TV SYSTEM
VCR OUTPUT CH
SELECT :a9
re) ENO: 0K
i © See RY
* NY STEN thote cw om
AUTO SET UP
MANUAL SET UP
VCR OUTPUT CH
SELECT : av SET cp
ENO 10K EXIT: MENU
Pe. what on "appropriate TV system. Select "G" for the
© ha, ag systenr or ( K ™ forthe D/K TV system.
4 Prose MIEN to exit the menu.
aac!
Selecting the TV system (23