Operation; Projecting A Picture; Turning Off The Projector; Positioning The Projector - ViewSonic Office Theater PJ1060 User Manual

Operation

Projecting a Picture

1 Power ON the projector. Set the MAIN POWER switch to ON (located
on the side Connector Panel). The ON indicator lights orange.
2 Press the STANDBY/ON button on the Projector Control Panel or on
the Remote Control Unit. (See page 7.)
The ON indicator blinks green during warm-up and stays green
when projector is ready for use.
NOTE: The power can not be turned on if the STANDBY/ON button
is pressed within 60 seconds after the power is turned off.
3 Remove the lens cap.
4 Position the projector the desired distance from the projection
screen, then set the projection angle by positioning the foot
E
adjusters. (See Positioning the Projector and Setting the Projection
N
Angle below.)
G
L
5 Power ON all connected input devices. (See page 5.)
I
6 Select the signal source: press the INPUT button on the projector or
S
one of the INPUT buttons (VIDEO/RGB) on the Remote Control Unit.
H
(See page 7.)
NOTE: To switch between RGB1 and RGB2, use the INPUT
menu (see page 10).
7 Using buttons on the Remote Control Unit or the control panel on top
of the projector, adjust the picture size with the ZOOM button, then
adjust the focus using the FOCUS button.

Positioning the Projector

The projector must be horizontal to get a distortion-free picture. Place the projector on a table-top or other flat
surface. Use the chart below to determine the placement of the projection screen.
D s i a t
S c e r e n
( n i
S z i e
( n i c h e ) s
M i i n m u m
4 0 5 5
6 0 8 5
8 0 1 1 4
1 0 0 1 4 4
1 2 0 1 7 6
1 5 0 2 2 0
2 0 0 2 9 1
Setting the Projection Angle
1 While firmly grasping the front of the projector with both hands, use
your index finger to push --and hold-- the Adjuster Buttons (located on
the sides of the projector).
2 While pressing the Adjuster Buttons, tilt the front of the projector up in
order to adjust the viewing angle. Then (while still grasping the
projector) release the Adjuster Buttons, securely locking the Front
Foot Adjusters.
3 To make fine adjustments, turn the base of the Front Adjusters.
CAUTION
• To prevent possible injury or damage to the projector, make sure
you are holding onto the projector securely before you unlock the
foot adjusters.
• Securely lock the Front Adjusters.
• Do not use unnecessary force when you move the foot adjusters.
Operation
6
n c e " a " D s i a t n c e " b "
c h e ) s ( n i c h e ) s
- - - - - - - - - - - - - - -
M a i x m u m
7 3 1
1 1 4 2
1 5 1 2
1 9 1 3
2 3 1 3
2 8 2 4
3 8 6 6

Turning Off the Projector

1 Press STANDBY/ON button (on Control
2 Wait until the fan stops (about one minute
3 Power OFF the projector. Set the MAIN
4 Place the lens cap over the lens.
Top View
Screen
CAUTION
To prevent a build-up of heat
that can damage the projector:
• Be especially careful not to block
ventilation holes when installing the
projector.
• Only use this projector in the horizontal
position (see Side View shown above).
Front View
Side View
Panel or Remote Control Unit) for one (1)
second. The ON indicator blinks orange
and the projector lamp turns off.
CAUTION: Always press the
STANDBY/ON button before turning
OFF the MAIN POWER. This allows the
fan to cool down the projector.
after pressing STANDBY/ON button).
POWER switch to OFF.
Side View
b
a
a = distance from projector
to screen
b = distance from center of
lens to bottom of screen
(a, b: +/- 10%)
Front Adjusters
You can make vertical adjustments
(0 to 9 degrees) using the Front
Foot Adjusters.
ViewSonic PJ1060