Napa Carlyle Tools 6-1156 Instruction Manual page 5

OPERATION
OPERATION NOTE: Always shut off air supply,
drain hose of air pressure and disconnect
tool from air supply when not in use, before
changing accessories or when making
repairs.
NOTE: Before using, test cut-off wheel by
briefly running the tool at full throttle under
a barrier (such as under a heavy work table)
to stop any possible broken wheel parts.
Always use the required wheel guard to prevent
injury from broken cutting parts. If a guard has
withstood a wheel breakage, discontinue its
use and replace it with a new guard. It may be
damaged. Position the guard between the cut-off
wheel and the operator. Use barriers to protect
others from wheel fragments and sparks.
Always wear impact-resistant eye and face-
protection to guard against flying debris
(users and bystanders). Even small projectiles
can injure eyes and cause blindness. A cut-off
wheel that breaks can cause very serious injury.
Daily measure the tool speed with a tachometer
to make sure the speed is not greater than the
RPM marked on the cut-off wheel. Never use a
cut-off wheel marked with a speed lower
than the tool speed.
When using the cut-off tool, be careful not to
exert excessive force. Too much force could be
hazardous if it causes the tool spindle tobend or
break. The burning of the work piece or excessive
speed reduction indicates too much force being
applied. Start the tool off the work, set it down on
the work evenly and move in the direction desired
to make the cut. When finished cutting, lift off the
work before stopping the motor.
WARNING: Correct cut-off wheel mounting is
necessary to prevent injury from broken
wheels. Do not use chipped or cracked cut-
WARRANTY
Important: DO NOT RETURN DEFECTIVE PRODUCT OUTSIDE OF ORIGINAL ONE (1) YEAR WARRANTY PERIOD TO
PLACE OF PURCHASE.
WARRANTY POLICY:
This Carlyle Air Tool is warranted against defects in material and workmanship for a period of One (1) Year from the date of
original purchase. We will replace, at our option, any part which proves to be defective in material or workmanship. Repairs or replacements are war-
ranted as described above for the duration of the original warranty period. In the unlikely event a replacement unit is required during this One (1) year
period, return the unit to your local NAPA Auto Parts Store for a replacement. This warranty does not apply to products which have been subjected to
abuse, misuse, modification, neglect, lack of maintenance, use in a production-related service, or repaired by anyone other than an Authorized Carlyle
Air Tool Service Center.
For complete listing of Authorized Master Repair Centers, see enclosed Customer Warranty Repair Form, or
visit www.toolwarrantyrepair.com
6-1156
off wheels. Cut-off wheels should be a free fit on
the spindle to prevent stress at the hole. Use only
wheel collars that come with the tool for mounting
the cut-off wheel. Flatwashers or other adapters
may over stress the wheel. Tighten the wheel on
the spindle to prevent spin off when the tool is
turned off.
WARNING: NEVER OPERATE THIS TOOL
WITHOUT REQUIRED DISC COVER/GUARD IN
PLACE.
Ensure an accessible emergency shut off valve
has been installed in the air supply line and make
others aware of its location.
To Assemble Cutting Wheel:
1. Secure Disc Retainer (27) with stop spanner
(37).
2. Remove nut (35) with stop spanner (37).
3. Place disc wheel onto spindle (27).
4. Reinstall nut (35) and tighten with stop
spanner (37).
5
Specifications
Horsepower ........................................ 0.9HP
Overall Length ................................ 4" Width
2.3"
Weight ............................................. 2.3 lbs.
RPM ..................................................18,000
Sound Level .....................................80 dBa
Vibration Level ...............................0.8m/s2
Air Consumption .............................3.5 CFM
Air Inlet Thread Size ....................... 1/4"-18
NPT Recommended Hose Size ..........3/8" I.D.
Recommended Air Pressure . 90psi (6.2 bar)
Throttle
Air Inlet
Rev. 05/22/23