CrimeStopper CS-2003DC SERIES II Installation & Operating Instructions Manual
  1. Manuals
  2. Brands
  3. CrimeStopper Manuals
  4. Car Alarm
  5. CS-2003DC II Series
  6. Installation & operating instructions manual
CrimeStopper CS-2003DC SERIES II Installation & Operating Instructions Manual

CrimeStopper CS-2003DC SERIES II Installation & Operating Instructions Manual

Remote control alarm system
Hide thumbs Also See for CS-2003DC SERIES II:
Table of Contents

Advertisement

Quick Links

CS-2003DC & CS-2003DC Series II
REMOTE CONTROL ALARM SYSTEM
INSTALLATION & OPERATING INSTRUCTIONS
CONGRATULATIONS on your choice of a Gargoyle™ Remote Alarm System by Crimestopper Security
Products Inc. This booklet contains the information necessary for installing, using, and maintaining your alarm
system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the
Tech Support number below.
*IMPORTANT INFORMATION: Primary and Optional Features:
-PRIMARY: These are features that must be connected in order for the system to operate properly; i.e. the
Siren, L.E.D., +12V Power, Ground, Doorpin, Override/Program/Valet Button etc.
-OPTIONAL: These are features to be connected if desired or agreed upon by the installing dealer. These
features may also require additional parts and/or labor fees. Consult with your installer beforehand; i.e. Door
Locks, Flashing Lights, Hood/Trunk trigger, and Auxiliary Remote Outputs etc.
TECH SUPPORT
Mon-Fri 8:00 AM-4:30 PM Pacific Time
(800) 998-6880
Website: www.crimestopper.com
Email: email@crimestopper.com
REV. D 7/2002 SW: T2, SC, HC, Latest: CH-(Green dot)
INTRODUCTION
This device complies with FCC Rules part 15. Operation is subject to the following
two conditions: 1) This device may not cause interference, and (2) this device
must accept any interference that may be received, including interference that may
cause undesired operation. The manufacturer is not responsible for any radio or
TV interference caused by unauthorized modification to this equipment. Such
modification could void the user's authority to operate the equipment.

Advertisement

Table of Contents
loading

Related Manuals for CrimeStopper CS-2003DC SERIES II

Summary of Contents for CrimeStopper CS-2003DC SERIES II

  • Page 1 CONGRATULATIONS on your choice of a Gargoyle™ Remote Alarm System by Crimestopper Security Products Inc. This booklet contains the information necessary for installing, using, and maintaining your alarm system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support number below.

  • Page 2: Table Of Contents

    TABLE OF CONTENTS Installation Cautions & Warnings…….………………………………………………………………………………2 Control Module Mounting………….……………………………………………..……………………….…………..3 Component Mounting………….…………………………………………………………….…………………..……..3 Wiring……..……………………………………………………………………………………………………….…….4-5 Power Door Lock Wiring...……………………………………………………….………..…………………………5-7 Transmitter Programming………………………………………………………………………………………………8 Option Programming…………………………………………….……………………………….………………….9-11 Custom Override……...………………………………………….……………………………….……………………12 Remote Control……………………………………..……………………………………………………….………….12 Operating Instructions………………………..……………………………………………………………..…….13-15 2 Vehicle Operation……….……………………………………………………………………………………………15 Car Jack Protection……………………………………………………………………………………...…………15-16 CS-2003 DC Series II Operation…..……..……………………………………………………………….………17-18 System Wiring Diagram……………………………………………………………………………………….………19 INSTALLATION CAUTIONS &...

  • Page 3: Control Module Mounting

    CONTROL MODULE MOUNTING DO NOT Mount the control unit in the engine compartment! DO NOT Mount the control unit or wiring harness where they can become entangled with moving parts such as brake/gas/clutch pedals, or the steering column! The alarm control module should be mounted in a concealed location. The Placement of the module will affect the distance from which the remote transmitter can control the unit.

  • Page 4: Wiring

    WIRING PIN 1: GRAY WIRE: INPUT SOURCE FOR REMOTE OUTPUT 1 RELAY Connect to a +12 Volt or Chassis Ground source depending on the output required for PIN 2 Gray wire See Below. PIN 2: GRAY WIRE: REMOTE OUTPUT 1 On-Board Relay (Optional) Connect this wire to an AUX device or Function.
  • Page 5 PIN 11: YELLOW WIRE: IGNITION SWITCHED “ON” +12 VOLTS INPUT Connect to an Ignition Wire (or Fuse in the fuse box) that shows +12 Volts power when the key turned “On”, when the car is “Cranking”, and when the car is running. PIN 12: ORANGE WIRE: NEGATIVE ARMED OUTPUT (500mA Ground, Optional) This wire becomes a (-) Ground output when system is armed.

  • Page 6: Power Door Lock Wiring

    POWER DOOR LOCK WIRING (ON-BOARD RELAYS) WHITE WIRE: DOOR LOCK [Switch Side, Term 87A] Reverse Polarity and Aftermarket Systems. GREEN: DOOR LOCK OUTPUT [Motor Side, Term 30] Reverse Polarity, Positive, Negative and Aftermarket Systems. BLUE: DOOR UNLOCK OUTPUT [Motor Side, Term 30] Reverse Polarity, Positive, Negative and Aftermarket. BROWN: DOOR UNLOCK [Switch Side, Term 87A] Reverse Polarity and Aftermarket Systems.
  • Page 7 SEPARATE DRIVER’S DOOR UNLOCK WIRING NEGATIVE TRIGGER DOOR LOCKS GREEN WHITE NOT USED GREEN BLUE BROWN VIOLET FUSED +12V DRIVER'S DOOR MOTOR +12V FUSED UNLOCK WIRE POSITIVE TRIGGER DOOR LOCKS GREEN WHITE NOT USED GREEN BLUE BROWN VIOLET FUSED +12V DRIVER'S DOOR MOTOR +12V...

  • Page 8: Transmitter Programming

    This system will learn a maximum of 3 transmitters total. 1. Turn Ignition ON/OFF…ON/OFF …ON. You should hear (3) chirps. 2. Press the Program/Override Button 5 times and you should hear 5 light flashes and 5 siren chirps. (System is now in transmitter programming mode.) 3.

  • Page 9: Option Programming

    PROGRAMMABLE OPTIONS 1. Turn the Ignition ON and press the Override/Program button 5 times. You should hear a long confirmation chirp. 2. Within the next few seconds, press the Override/Program button [again] the number of times that corresponds to the feature list below. The siren will chirp for each button press. DO NOT LOSE COUNT!! 3.
  • Page 10 OPTION PROGRAMMING 1. HORN CHIRPS / PULSES This option controls the system’s Factory Vehicle Horn output. There are 3 selections: Button 1 (Lock) = Horn Pulse only when alarm is tripped. Button 2 (Unlock) = Horn Chirps for Arm / Disarm and Pulse when tripped. Button 3 (Trunk) = Horn Chirps for Arm, Disarm, and Pre-warning protection while it still pulses when tripped.
  • Page 11 OPTION PROGRAMMING 9. PARKING LIGHTS ON WITH DISARM Keeps parking lights on instead of 2 flashes when system is disarmed to assist in locating your vehicle in a crowded parking lot or structure. Light will stay on for 30 Sec. or until Ignition is turned on. 10.

  • Page 12: Custom Override

    CUSTOM OVERRIDE Custom override allows the user to set a specific number of button presses (2-15) required to perform an emergency override/disarm of the alarm system. This increases the level of security of the system, but you MUST MEMORIZE how many button presses you have changed your system to use or the unit will not disarm in an emergency. 1.

  • Page 13: Operating Instructions

    OPERATING INSTRUCTIONS ACTIVE ARMING To arm the alarm and lock the doors, press the #1 (Lock Symbol) button on the transmitter. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock and the starter will be disabled if these optional features are installed.
  • Page 14 OPERATING INSTRUCTIONS PROGRAMMABLE SILENT ARM/DISARM MODE The system can be silently armed and disarmed as normal with Lock/Unlock Buttons, but no siren chirp. See alarm programming option (8) to enable or disable this feature. EMERGENCY OVERRIDE / DISARM If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to open the door with the key, which will activate the alarm.

  • Page 15: Vehicle Operation

    OPERATION OPEN ZONE ALERT/BYPASS If the system detects a faulty or open zone (Door left open) when the system is ACTIVELY ARMED, the siren will chirp 4 times along with 4 light flashes. The faulty zone will be automatically bypassed. IGNITION-CONTROLLED DOORLOCKS The doors will automatically lock when the ignition is turned on and will unlock when the ignition is turned off.

  • Page 16: Car Jack Protection

    CARJACK PROTECTION PASSIVE CARJACK This feature provides Passive Carjack protection and must be enabled before use through Alarm programming options (13) & (14). See page 9. We recommend this mode should only be used in serious situations. When the Ignition is on (vehicle is running), and a door is opened, the Carjack countdown sequence will be initiated. 90 Seconds later, the unit will begin a Carjack Cycle consisting of 15 seconds of pre-warning chirps turning into a full system activation with siren/flashing light pulses for up to 5 min.

  • Page 17: Cs-2003 Dc Series Ii Operation

    “SUPER BRIGHT” BLUE LED / VALET BUTTON POD LED POD SYSTEM VALET/PROGRAM BUTTON CS-2003DC SERIES II BUTTON 1 BUTTON 3 PANIC *GREEN LED Blinks once for Bank 1 and twice for Bank 2. DUAL ADJUST Smart Sense™ Shock Sensor: >Use the Green screw for Pre-warn adjustment >Use the Red Level for Shock trigger adjustment...
  • Page 18 CS-2003DC SERIES II LED / VALET BUTTON MOUNTING: IN DASH UNDER DASH "L" Bracket...

Table of Contents