Table of Contents
Advertisement
Disc Repeat
The Disc Repeat function causes the same
disc to play repeatedly.
1.Press button [17] for 2 seconds or more
while the desired disc is being played.
The mode wil! change to Disc Repeat
mode ("D.RPT" [36] appears).
2.To cancel Disc Repeat, again, press but-
ton [17] for 2 seconds or more and turn
off "D.RPT" at [36].
Using Fast Forward and Reverse
1.Press simultaneously both (+) and (-)
sides of the button [7].
At this time the dispiay will show the
amount of elapsed disc play time.
2.Press the (+) side of button [7] for fast for-
ward, and the (—) side for reverse.
Sound is output during fast forward and
reverse operations.
The display counts down the number of
seconds between tracks if the spacing is
rather large (-'00"-'01").
Using Program Play
This function lets you program the play se-
quence of all of the tracks contained on the
compact discs loaded in the magazine.
The ITP function will not operate when
connected to either the CDX-M70 or CDX-
M100.
Up to 32 selections can be programmed
for a single magazine.
Up to 16 different magazines (max. 32 se-
lections per magazine) can be pro-
grammed individually. If you program
more than 16 magazines, old programs
are automatically replaced by new ones.
Automatic Magazine Program Selection
(AMPS) retrieves the right program from
the memory automatically, as soon as a
preprogrammed magazine is loaded.
Preprogrammed magazines are identified
using the CD in the tray 1 of the maga-
zine. Therefore be sure that tray 1 con-
tains a disc.
Programming
1.While a disc is playing, select the desired
disc and track you want to program.
2.Press button [15] to memorize the track
being played.
("P-01" is indicated during the memory
step.)
3.Procedures 1 and 2 above can be repeat-
ed until a maximum of 32 steps are pro-
grammed.
If the 33rd step is selected, the "FULL"
display will appear, indicating that no
more selections can be programmed.
When there are already a number of se-
lections in the memory, the new selection
will be added to the last step.
Playing Back the Program
1.Hold down button [15] for 2 seconds to
begin play in the programmed sequence,
while a disc is playing.
("PP01" is indicated during the step
where the program is played.)
2.Press button [15] again to cancel program
play.
Pressing the (+) or (-) side of button [7]
during programmed play makes it possi-
ble to search for a specific step number
from among the programmed selections.
Program play returns to the first step in
the programmed sequence when it reach-
es the end of the program.
When playing a magazine that has no
program recorded, "PPOO" will be dis-
played for approximately 3 seconds.
Erasing the Program
It is possible to erase one or all selections
of the program in the magazine being
played.
To erase a single selection:
1.Press the (+) or (-) sice of button [7] dur-
ing programmed play. and search for the
specific step you wish to erase.
2.Press button [6] for at least 2 seconds and
the selection being played will be erased.
+ After the particular track has been erased,
the tracks in the next position move from
down up one riotch in the order from the
previous position.
To erase the entire program:
While a disc is playing, hold down button
[6] for at least 2 seconds. All the programs
in the magazine being played will be
erased,
("P-CL" is indicated on the display.)
Error Mode
Should an abnormality occur — for exam-
ple, Multi-Play CD Player cannot be operat-
ed, or the music stops during CD playback
— the main unit will indicate an error
mode. (Example: "E-11")
While it the unit is in error mode, a number
will be displayed indicating the cause of the
error, sO please check the items listed be-
low. If you cannot fix the problem after
checking the cause of the error, please con-
tact your dealer or your nearest Pioneer
service center.
Note:
When using the Multi-Play CD Player, CDX-
M100, CDX-M70, CDX-M50 and CDX-M40,
an error will be displayed only in the form
of "E-00", without the number which indi-
cated the cause of the error. When this dis-
play appears, please check items 11, 12, 14,
or 30 listed below.
Display
Cause
Treatment
Dirt or a scratch on the disc stops the
Wipe the dirt off the disc.
11.12
laser beam from being able to focus.
Exchange the disc if it is scratched.
14
down.
:
right side up.
An unrecorded compact disc (CD-R),
When you use a CD-R, load one that
can be recorded on once is being used. | has been recorded on.
30
Dirt or a scratch on the disc hinders the | Wipe the dirt off the disc.
track number search function.
Exchange the disc if it is scratched.
a
multi-play CD player.
An empty magazine is Joaded in the
a.
insert a disc in the magazine.
10, 12,
50, 60,
70, AO
Electrical or mechanical system fault.
Turn the car ignition switch OFF, then
ON again, or change to other sources
except CD playback , and then to CD
playback again. If the error indication
does not disappear, contact your deal-
er or your nearest Pioneer service sta-
tion.
* When error numbers not mentioned above are indicated, refer to the owner's manual ac-
companying the multi-play CD player.
Advertisement
Table of Contents
