Philips 107T50/00 Service Manual page 49

LightFrame for Windows (Continued)
kK Go to cover page
5. Click Yes,
bring up Fig.5
6. Click Next,
bring up Fig.6
Linenne Agrinement
Pleaor rend the foloweng hvense ayrwemert carehay,
reed list PAGE DOWN kato sue ths vost ts eeernert :
EASE READ THE FOLLOWING TERME AND CONDITIONS CAREFULLY you fend
lunes, ether an aevicy of on incivicksal) dc and conditions,
lon the "No™ Gunton ersdlox doves opal toe sottrate 7 ThE pd User Learee agreement
je coniract patina zou arid Peden Communes Elocherice 9.V. _ Tahuing i cuppa and
Segoe nest
the terne and candtions of thie ree Ens U nae
sie vie THE LENSE 'SOFTWARE AL ARNO GES THAT YOU.
poets w n s rt narnet:
receding Unorae Area w. wot wi clone Tenadi gener malaga aoreatart:
7. Click Next,
bring up Fig.7
Setup Type
Bom mverea muta neaes rears st
Luter seme has to brie ¢ yx) are ating «ORT oF 4 LCD mordor, Pleate indicate the tre it |
Pips monitor you we wang. :
To cordam the bre theece ok up Ure eal nurnbes oF Yow bon left Gort your mara
< n thie prodded pander walt oath 15D, 170 o1 180 (e.g. 190F3] you have @ LCD moniter, If the.
ocd atti stars orth 108, 107 cr VOB e.. 1077 Al xe hee @ CAT eroritor,
*Plaore miidke wor vetestion butom: *
8. Click Next,
bring up Fig8 & Fig 8 Fig 8
9. Click Finish,
bring up LightFrame 3, Fig. 10 on the desktop. Fig 10
Uninstall
Should you need to remove the LightFrame software, please follow
these steps.
1) First, click on the Start Menu.
2) Next, highlight Settings.
3) Then, click on Control Panel.
4) Now, click on Add/Remove Programs
5) Finally, select LightFrame from the list and then click on the
Add/Remove button.
LightFrame for Windows (Continued)
Operating LightFrame
After installation, LightFrame starts up automatically whenever the
computer is started. At system start up, LightFrame checks the selected
resolution of the monitor and If the monitor is LightFrame capabie.
Icon and Colors
An icon of a monitor represents LightFrame on your desktop. This icon
appears as a shortcut on the Windows desktop. LightFrame has three (3)
modes of operation: Active, Inactive, and Suspended, The same icon
with a different color in its center represents each mode.
Active = The LightFrame taskbar as below.
else
olsicicy
Bae
An active window must be 100% visible, i.e. it must be on top of all other
windows or areas. If any part of another window or area overlaps a
highlighted window, LightFrame automatically suspends operation. Once
that window or area is removed and the original highlighted window is on
top again, LightFrame automatically re-engages and the icon regains its
bright green center.
Inactive = The taskbar as below.
Suspended = The taskbar as below.
Notes
An active window must also be 100% on the monitors viewing area. If
part of a highlighted window moves off the monitors viewing area,
LightFrame automatically goes Into the Suspended mode. If part of a
window Is off the viewing area, you will not be able to use LightFrame on
that window.
Only one window or area at a time can be highlighted.
How To Activate LightFrame
1) Click on the LightFrame icon wy Fig. A in the systemtray. The icon
will be changed to #44 Fig.B: vB ae
wezicy
Fig.B
2) Guide the mouse to the window you want displayed. As you move the
mouse, the cursor changes to a small arrow with a light bulb.
3a) Click on the window you want to have highlighted. The brightness
and sharpness are automatically adjusted.
i
ltt Go to cover page
3b) if you want to highlight only an area of a window, click on the fett
mouse button and drag the cursor over the area to be highlighted while
holding the mouse button. A rectangle forms around the area. When the
area is encompassed by the rectangle, release the mouse button and
the area becomes highiighted.
How to Deactivate LightFrame
To deactivate, click on the LightFrame icon in the System Tray of the
Taskbar. Click Icon, as Fig.1and Taskbar will be changed to Fig. 2
and LightFrame is deactivated.
If a highlighted window is closed before LightFrame is deactivated,
LightFrame is automatically deactivated.