IKEA LAGAN Manual page 6

ENGLISH
away from the installation site. After
unpacking the appliance, make sure that it
has not been damaged during transport.
In the event of problems, contact the
dealer or your nearest After-sales Service.
Once installed, packaging waste (plastic,
styrofoam parts etc.) must be stored out of
reach of children - risk of suffocation.
The appliance must be disconnected from
the power supply before any installation
operation - risk of electrical shock. During
installation, make sure the appliance does
not damage the power cable - risk of fire or
electrical shock. Only activate the appliance
when the installation has been completed.
Connect the dishwasher to the water
mains using only new hose sets. The old
hose sets should not be reused. All hoses
must be securely clamped to prevent them
coming loose during operation.
All local waterboard regulations must be
complied with.
Water supply pressure 0.05 - 1.0 MPa.
The appliance must be placed against
the wall or built into furniture to limit the
access to its rearside.
For dishwashers having ventilation
openings in the base, the openings must 6
not be obstructed by a carpet.
If installing the dishwasher at the end
of a row of units making the side panel
accessible, the hinge area must be covered
to avoid risk of injury.
The inlet water temperature depends on
the dishwasher model. If the installed inlet
hose is marked "25°C Max", the maximum
allowed water temperature is 25°C. For all
other models the maximum allowed water
temperature is 60°C. Do not cut hoses
and, in the case of appliances fitted with
a waterstop system, do not immerse the
plastic casing containing the inlet hose
in water. If hoses are not long enough,
contact your local dealer. Make sure the
inlet and drain hoses are kink-free and are
not crushed. Before using the applinace
for the first time, check the water inlet
and drain hose for leaks. Make sure that
the four feet are stable and resting on
the floor, adjusting them as required, and
check that the dishwasher is perfectly
levelled using a spirit level.
Use the appliance only when the covers
shown on diagram 19 in the Assembly
instruction are correctly assembled - risk
of injury.
ELECTRICAL WARNINGS
The rating plate is on the edge of the
dishwasher door (visible when the door is
open).
It must be possible to disconnect the
appliance from the power supply by
unplugging it if plug is accessible, or by
a multi-pole switch installed upstream of
the socket in accordance with the wiring
rules and the appliance must be earthed in
conformity with national electrical safety
standards.
Do not use extension leads, multiple
sockets or adapters. The electrical
components must not be accessible to
the user after installation. Do not use the
appliance when you are wet or barefoot.
Do not operate this appliance if it has
a damaged power cable or plug, if it is
not working properly, or if it has been
damaged or dropped.
If the supply cord is damaged, it must
be replaced with an identical one by the
manufacturer, its service agent or similarly
qualified persons in order to avoid a
hazard - risk of electrical shock.
If the fitted plug is not suitable for your
socket outlet, contact a qualified technician.
Do not pull the power supply cable. Do not
immerse the mains cord or plug in water.
Keep the cord away from hot surfaces.
ELECTRICAL CONNECTION FOR GREAT
BRITAIN AND IRELAND ONLY
Fuse replacement.
If the mains lead of this appliance is fitted
with a BS 1363A 13amp fused plug, to
change a fuse in this type of plug use an
A.S.T.A. approved fuse to BS1362 type and
proceed as follows:
1. Remove the fuse cover
A
B
2. Fit replacement 13A
3. Refit both into plug.
Important:
The fuse cover must be refitted when
changing a fuse and if the fuse cover is lost
the plug must not be used until a correct
replacement is fitted.
Correct replacement are identified by the
colour insert or the colour embossed in
words on the base of the plug.
Replacement fuse covers are available
from your local electrical store.
(A) and fuse (B).
fuse into fuse cover.
6