Advertisement
HITo omit unwanted material during
edit-recording
Pause)
Press the pause button.
Deck 2 will change to the recording stand-by mode, and playback
will continue on deck 1.
Press the playback button corresponding to the side of the tape
being recorded when the tape reaches a point where you want
to record.
Wi To locate a certain tune while an edit-recor-
dings is being made
1. 'stop
Press the stop button of deck 1.
(A silent interval of about 4 seconds will then be made on the
tape in deck 2, and then deck 2 will change to the recording
stand-by mode.)
2.
[review], {cue
Press the fast-forward/cue
or rewind/review
button of
deck 1 and locate the desired tune.
3. [synchro start
To resume recording, press the synchro-start button.
To erase recorded sounds
When
new
recordings are made
on a pre-recorded tape, all
sounds recorded on that portion of the tape are automatically
erased. To erase a tape without making a new recording, follow
the steps below.
1. Insert the recorded cassette into the cassette holder of
deck 2.
2. Set the recording-level controls to "0".
3. Set the reverse-mode
selector to either one-side only
(=) or both sides (>).
4. Press the Dolby noise-reduction button corresponding to
the Dolby noise-reduction indicator that is illuminated.
(The indicator will then switch OFF.)
5. Press the record button.
6. Press the playback button corresponding to the side to be
erased.
When a Technics compact disc player with the compact disc
synchro-edit
function
is used
in combination
with this unit,
recordings can be made on side "A" and side "'B"' of the tape,
without
interruptions
of tracks,
in conjunction
with the tape
length.
2. Press the stop button. (Disc play will stop.)
3. Press the edit-tape-length button and specify the length
of the tape to be used.
The tracks to be recorded to side 'A'' of the tape and those to
be recorded to side ''B" will then be automatically selected
according to the tape's length.
4. Press the play button.
The recording will start at the same time that play starts at the
compact disc player.
- Notes:
e Recordings cannot be made on the leader tape (attached to
each end of recording tape), so advance the tape slightly
from its end before starting a recording. Also check to be
sure that side A ("fwd") indicator is illuminated.
elf the CD program contents to be recorded on side ''A" of
the tape are shorter than the actual tape length, this unit will
continue to record until it reaches the end of side ''A'', while
the compact disc player switches to the pause mode. At the
end of side 'A'.
deck 2 automatically switches to side ''B"
and after few seconds the compact disc player will resume
play.
¢ When canceling the synchro-edit recording mode, press the
stop button on the compact disc player and then press the
stop button on this unit. (To cancel mid-way through a perfor-
mance,
press the stop button on the compact
disc player
twice in succession.)
Automatic-record-muting function
By simply pressing the automatic-record-muting button while a
recording is being made, a silent interval (which is necessary for
locating the beginning of a tune during playback) can be made.
Automatic-record-muting button (auto rec mute)
8 Of
|
Sie
Lier
o
| CICA SE}
as5 0
j ETH |
1
OF ee
a [25
ae a
While recording, press
the automatic-
To resume recording,
press the playback
button corresponding
to the side being
recorded.
record-muting button
one time.
FM broadcasts |
A) | Commercial
ADA
(
announcements,
etc.
This unit will record a silent interval (4 seconds long) between
tunes,
and
then
will
change
to the
recording
stand-by
mode.
Record mode
| Fi 4 | |
HE To make a silent interval of more than 4 seconds on the
tape
Press and hold the automatic-record-muting button for
the necessary number of seconds.
The unit will change to the recording stand-by mode when
the button is released.
Advertisement
