Philips DVD612/001 Service Manual page 12

GB 22 5. DVD612 /XX1
5.2 PLAYER SCRIPT
5.2.1 Purpose of Player Script
The Player script will give the opportunity to perform a test
that will determine which of the DVD player's modules are
faulty, to read the error log and error bits and to perform an
endurance loop test. To successfully perform the tests, the
DVD player must be connected to a tv set to check the output
of a number of nuclei. For DVDv2b a multi-channel amplifier,
a set of 6 boxes and an external video source are necessary
to test. To be able to check results of certain nuclei, the
player script expects some interaction of the user (i.e. to
approve a test picture or a test sound). Some nuclei (e.g.
nuclei that test functionality of the Basic Engine module)
require that the DVD player itself is opened, to enable the
user to observe moving parts and approve their movement
visually. Only tests within the scope of the diagnostic
software will be executed hence only faults within this scope
can be detected.
5.2.2 Contents of Player Script
The player script contains all nuclei that are useful on a DVD
player that is connected to a tv-set and help to determine
which module of the DVD player is faulty, as well as to read
out the contents of the error logs.
5.2.3 Structure of Player Script
The player script consists of a set of nuclei testing the three
hardware modules in the DVD player: the Display PWB, the
Digital PWB and the Basic Engine.
Nuclei run by the player test need some user interaction; in
the next paragraph this interaction is described. The player
test is done in two phases:
1. Interactive tests: this part of the player test depends
strongly on user interaction and input to determine
nucleus results and to progress through the full test.
Reading the error log and error bits information can be
useful to determine any errors that occurred recently
during normal operation of the DVD player.
2. The loop test will loop through the list of nuclei
indefinitely, till the NEXT key is pressed. The list of nuclei
is as follows:
• VideoColSetupComm
• VideoScartSwComm
• PapChksFlash
• PapI2cNvram
• CompSdramWrR
• PapS2bEcho
• PapI2cDisp
For DSW version 1.6 and above. the DSW version number
will be displayed on the local display. Press NEXT to
continue to the display test.
The display should look like the following:
Figure 5-3
Diagnostic software descriptions and troubleshooting
CL 16532007_002.eps
010201
www.rtv-horvat-dj.hr
5.2.4 Survey
Press 2 keys simultaneously
<OPEN/CLOSE> + <STOP>
Connect to mains
INTERACTIVE TESTS
DISPLAY PCB
DISPLAY TEST
LED TEST
KEYBOARD TEST
REMOTE CONTROL
P50 LOOP BACK TEST
MONO PCB
DIGITAL PART
PICTURE TEST
SOUND 1 TEST
SCART DVD TEST
SCART LOOP TEST
SOUND 2 TEST
MONO PCB(SERVO)
& BASIC ENGINE
VERSION NUMBER
TRAY TEST
SLEDGE TEST
DISC MOTOR TEST
FOCUS TEST
RADIAL TEST
JUMP TEST
TRAY TEST
ERROR LOG & BITS
LOOP TEST
To exit player test,
disconnect from mains
Figure 5-4
DispDisplay(30)
DispLed(29)
DispKeyb(27)
DispRc(28)
DispP50(60)
VideoColDencOn(23a)
AudioPinkNoiseOn(20a)
VideoScartSwDvd(54a)
VideoScartSwPass(54b)
AudioSineOn(21a)
BeVer(37)
BeTrayOut/In(43ab)
BeSledgeOut/In(41ab)
BeDiscMotorOn(39a)
BeFocusOn(38a)
BeRadialOn(40a)
BeGroovesIn/Mid/Out(42abc)
BeTrayOut/In(43ab)
LogReadErr(31)
LogReadbits(32)
= Dealer script exclusive of test2
CL 16532007_003.eps
300101