Cleaning The Particle Trap; Cleaning The Hygienic Exhaust Filter; Spare Parts And Accessories; Before You Send In The Appliance - Dirt Devil Proxima M5052 Operating Manual

5 Maintenance

5.3 Cleaning the particle trap

A
1
13

5.4 Cleaning the hygienic exhaust filter

A
14

5.5 Spare parts and accessories

ATTENTION:
Only use original spare parts from the scope of delivery or those that you
have acquired by reordering.
„ Ordering address: Zpage 48, „International Service".
„ Further information: Z www.dirtdevil.de
„
The following accessories and spare parts can be reordered:

5.6 Before you send in the appliance

WARNING:
Danger of injury! Never use a defective appliance! Always switch off the
appliance and disconnect it from the mains before starting troubleshoot-
ing Zchapter 4.3, „Switching off".
Before contacting your authorised Dirt Devil dealer, Dirt Devil service part-
ner or appliance market or sending in the appliance, first follow the proce-
dure in the following table to check if you can solve the problem yourself.
Problem
The appli- The socket does not carry current.
ance will
Test the vacuum cleaner at another socket which you are
not start
sure carries current.
Power cord is damaged. Have the power cord replaced by
Dirt Devil Customer Service, address, Zpage 48,
„International Service".
The vacu- The overheating protection has tripped (possibly due to
um cleaner blocked suction channels, filters, or similar).
stops sud-
Switch the appliance off and pull the plug out of the socket.
denly.
Remove the cause of overheating (e. g. by disassembling
telescopic tube and suction hose and removing the obstacle
and/or cleaning filters). Wait for about 45 minutes. After the
appliance has cooled off, you may switch it on again.
Cleaning The dust container is full.
Empty / clean the dust container, Zchapter 5.1, „Emptying
indicator
and cleaning the dust container" and Zchapter 5.3, „Clean-
(Fig. 1/13,
optional)
ing the particle trap"
lights up.
B
B
Solution
1. Switch off the appliance, Zchapter 4.3, „Switching off"
2. Remove the dust container Zchapter 5.1, „Emptying and cleaning the
dust container".
3. If dirt is visible in the suction channel (Fig. 13/A1), lay the appliance on
its side.
4. Open the particle trap by twisting it off (Fig. 13/B). The dirt will fall out
of the opening. If necessary, help a bit by hand.
5. Empty the dirt into a dustbin.
6. Close the cleaned suction channel by refitting and fastening the particle
trap.
7. If you haven't done this by now, firmly push the dust container back into
its receptacle. Check that it is securely fitted..
1. Switch off the appliance, Zchapter 4.3, „Switching off"
2. Push the release catch of the exhaust filter cover down (Fig. 14/A) and
fold down the exhaust filter cover.
3. Remove the exhaust filter (Fig. 14/B).
4. Tap the exhaust filter over a dustbin for a rough cleaning. Remove larg-
er agglomerations of dirt by hand.
5. Remove residual dust with a soft brush, e.g. the supplied furniture
brush.
6. Ifthe filter is damaged or deformed, replace it.(ordering information
Zchapter 5.5, „Spare parts and accessories").
7. Place the clean/new exhaust filter back into its fitting.
8. Attach the exhaust filter cover at the bottom side first and then fold it
upwards.
Item number
5050001 1 Dual motor protection filter (2 pieces: foam plastic filter
element (Fig. 1/19) and filter holder (Fig. 1/20))
5050002 1 hygienic exhaust filter
5050003 1 particle trap
M203 1 parquet brush
M209 1 turbo brush
Problem
The clean- The bypass vent (Fig. 1/24) is open.
ing results
Close the bypass vent (Fig. 1/24).
are unsat-
The attached nozzle is unsuitable.
isfactory in
Change the nozzle Zchapter 3.2, „Selecting the proper noz-
spite of the
zle"
appliance
The position of the "carpet/hard floor" selector (Fig. 1/28) is
working
unsuitable.
correctly.
Set the "carpet/hard floor" selector (Fig. 1/28) to the correct
position for the type of floor, Zchapter 4.2, „Vacuum clean-
ing", step 4.
The dust container is full.
Empty / clean the dust container Zchapter 5.1, „Emptying
and cleaning the dust container".
The filter is dirty.
Change/clean the respective filter Zchapter 5.2, „Cleaning
the cyclone unit and the dual motor protection filter" or
Zchapter 5.4, „Cleaning the hygienic exhaust filter".
Nozzle, telescopic tube or suction hose are blocked.
Remove the obstacle. If necessary, use a long wooden stick
(e.g. a broomstick) to do this.
Description
Item number Description
M219 1 mini turbo brush
M232 1 long crevice nozzle
Solution
15