Table of Contents
Advertisement
Using the Wireless Remote Control
The wireless remote control can be operated regardless of the hold mode of the unit.
[Preparation
| [Operation
Installing the lithium battery
Reverse side of
remote control
@Do not place any object which will block the path of
the signals between the remote control and the unit.
®Do not allow the remote sensor or transmitter to be-
come dusty.
©Do not leave the remote control standing in direct sun-
light or in high temperature locations in a car.
eln the interest of traffic safety, do not operate the re-
mote control while driving.
Take every care to prevent small children from putting
the lithium battery in their mouths or swallowing it. In
the event that a child has swallowed a battery, consult
with a physician immediately.
CAUTION:
The battery used in this device may present a risk
of fire or chemical
bum
if mistreated.
Do not
recharge, disassemble, heat above 100°C (212°F),
or incinerate. Replace battery with Panasonic part
number CR 2025/1P0D only. Use of another battery
may present a risk of fire or explosion.
Dispose of used battery promptly. Keep away from
children,
Do not disassemble and do not dispose of in fire.
Preparation:
When the unit is to be operated using rechargeable batteries or dry cell batteries, first press > H on the unit and
then use the remote control. (The unit cannot be operated by the remote control while the unit is turned off.)
Initiates play/establishes pause mode when pressed again.
Stops play/turns the unit off when kept depressed.
Skip tracks (tap).
Rapidly searches forward or backward during play (keep
depressed).
Repeat all track or single track.
Remote control's operating range
Point the transmitter on the remote contro! at the re-
mote sensor on the unit.
Use the remote control within a 7-meter range of the
remote sensor on the unit.
(Depending on the angle of the remote control, the
signals may not reach the sensor.)
Using the Unit with Optional Accessories
How to use the Velcro tape
To prevent misptacement of the remote control, it is re-
commended that the Velcro tape be used as shown in
the figure below.
Back of remote control
Adhere the Velcro tape roughly in the center of the re-
mote control's back surface.
Before adhering the Velcro tape, choose a flat and
even surface and wipe off any dirt.
Avoid a location which is exposed to direct sunlight.
Using the unit with an audio
system
Using a stereo connection cable (not included), you can
hear CDs on your audio system.
Connect the cable to the amplifier after turning off its
power.
Do not connect the cable to the PHONO jacks on the
amplifier.
eObtain the optional connecting cable if the amplifier
comes with mini-phone jacks.
e Adjust the volume on the amplifier.
Sound quality changes when XBS is selected, but vol-
ume is reduced by approximately fifty percent.
Back panel of the unit
Amplifier
To CD or AUX
b terminals
Stereo connection cable (not included)
Using the unit with a car audio
system
The SL-S231C and SL-S232C come with the car adap-
tor and car stereo cassette adaptor.
Items to be purchased (SL-S230/SL-S235)
For connection to the car audio system:
Car stereo cassette adaptor (GH-CDM10A)
Connect the car stereo cassette adaptor
to the unit's headphones jack.
(When doing this, keep the unit's VOLUME
control at a setting between 4 and 6.)
aeerrtere terns vereer
Seta
For securing
the unit and
connecting
the
power supply:
Car adaptor (SH-CDC9)
Car mounting kit (SH-CDF7)
Car mounting arm, Car insulator
It may not be possible to use the unit with some types of
car stereo owing to restrictions imposed by the con-
struction of the car stereo cassette adaptor.
For further details, refer to the instructions of the part
concerned.
Advertisement
Table of Contents
