Table of Contents
Advertisement
200M ENTERTAINER STEREO MIXER
OWNER'S MANUAL
SPECIFICATIONS
CONDITIONS
1. All noise measurements are made through mic
inputs with: 150 Q source, 20 Hz - 20 kHz noise
bandwidth.
2. 0 dBu = 0.775 V rms across any impedance.
POWER OUTPUT
4 Q load: 300 W/per channel
8 Q load: 200 W/per channel
FREQUENCY RESPONSE
Power Amplifier: 20 Hz - 20 kHz ± 1 dB with a
4 Q load
Mixer: Microphone input to any output, EQ flat,
gain controls nominal 20 Hz - 20 kHz ± 1 dB
THD
Power Amplifier: < 1 % at maximum rated power
with a 4 to 8 Q load
<0.2 % at 100 W with a 8 Q load
Mixer: <0.1 % at+20 dBu, 20 Hz-20 kHz
(
NOISE LEVEL
-123 dBu EIN-equivalent input noise, microphone
input (150 Q termination)
-90 dBu residual at MAIN OUT, MONITOR OUT,
SUB L , SUB R (all gain controls at minimum)
-70 dBu residual at MAIN and MONITOR; all input
gain controls at minimum, MAIN and MONITOR
at 0 dB
INPUT CHANNEL EQUALIZATION
± 15 dB low boost/cut centered at 90 Hz
± 12 dB mid boost/cut sweepable from 300 Hz to
5 kHz
± 15 dB high boost/cut centered at 10 kHz
SUBMASTER INSERTS
1/4-in. stereo phone jack, tip send, ring return
MICROPHONE INPUTS
Type: low-impedance, balanced, pin 2 positive
Maximum Input Level: +14 dBu (3.9 V rms)
Input Impedance at 1 kHz: 2 kQ
CLIP INDICATOR THRESHOLD
2 dB below preamp clipping
LINE INPUTS
Type: high-impedance, balanced, tip positive
Maximum Input Level: +30 dBu (24.5 V)
Input Impedance at 1 kHz: 20 kQ
TAPE INPUTS
Types: high-impedance, unbalanced, tip
positive, RCA phono jack, 1/4-in. stereo phone
Input Impedance:
RCA phono: 6 kQ
1/4-in. phone: 20 kQ
GRAPHIC EQUALIZER
9-band, Constant Range12 dB boost/cut
Center Frequencies: 50,100, 200, 400, 800,1600,
3150, 6300, 12,500 Hz
MAXIMUM VOLTAGE GAIN (± 3 dB)
79 dB-MIC IN to MAIN OUT
69 dB - LINE IN to MAIN OUT
79 dB - MIC IN to MONITOR OUT
69 dB - LINE IN to MONITOR OUT
86 dB-MIC IN to EFX SEND
76 dB - UNE IN to EFX SEND
46 dB - TAPE IN(RCA phono) to MAIN OUT
36 dB - TAPE IN (1/4-in.) to MAIN OUT
79 dB-MIC IN to SUB Lor R
69 dB-UNE IN to SUBLorR
CROSSTALK
-75 dB - Adjacent inputs: 1 kHz
-75 dB - Input to output: 1 kHz
-50 dB - All combinations: 20 Hz - 20 kHz
EFFECTS PROCESSOR
16-bit digital, stereo, 15-kHz bandwidth, 30
user-selectable programs
MAXIMUM POWER INDICATOR (FOR EACH
CHANNEL)
Ughts when compression circuit is activated by
clipping
DIMENSIONS
Height: 7.94 in. (20.2 cm)
Depth: 18.25 in. (46.4 cm)
Width: 19.5 in. (49.5 cm)
WEIGHT
38 lb (17.3 kg)
POWER REQUIREMENTS
100/120/220/240 V ac, 50/60 Hz (internal setting)
CASE
Black polyethylene with detachable line cord
OPTIONAL ACCESSORIES
EPC-200M carrying case
S-200 equalizer
S-200 speakers
Specifications subject to change without notice.
three
Advertisement
Table of Contents
