Advertisement
tt (O960S°0N)
Front Panet
The "ON TIMER" feature allows you to turn on your TV
~ automatically at a preset time and on a specific channel. The ON
TIMER is available for 2 different settings.
With "PAGE-2" (or "PAGE-1" or "PAGE-3") MENU displayed
on the screen, press "5" of 10-Digit Keypad @® . The display
will show:
OPA
EL O8 <hO>
© At this time, if the display of POWER (NTERRUPTED/
WOULD
YOU
SET CLOCK
FIRST?" (which may appear
during the SLEEP TIMER procedure) appeais, it shows that ,
the clock is not operating, and the ON TIMER will not func:
tion.
'
Press "1" (YES) to set the clock, {If "2" (NO) is pressed, the
warning message "YOU CANNOT OPERATE ON TIMERIt"
is displayed.)
;
Set the clock. See "6. SET CLOCK" on page 15 for details
regarding clock setting. After the clock has been set, the mes-
sage "THANK
YOU! 1!' appears to show that the clock has
just been adjusted and the ON TIMER is now ready to be set.
Two different settings are possible. Press "1" or "2" to select
the setting position. The display will show:
@ The second from the bottom fine shows the preset time if
already previously set.
1) SET
Press "1" to start the ON TIMER
for turning the TV on
automatically
at the
preset time
shown.
"<YES>"
ap-
pears to show that the ON TIMER has started.
2) CANCEL
Press 2" to cancel the setting. "<NO>" appears to show
that the ON TIMER has been cancelled.
3) CHANGE
Press "3" to re-adjust the setting. Then, the following display
appears.
ON TINE
~~~
Press the numbers on the 10-Digit Keypad to set the desired
switch-on time. For example, if you want the TV to switch
on automatically for CHANNEL
12 at 7:00 AM, press, 7',
"0" and 0'.
(When you select ''1'" for hour setting, ré-
member to press ''0" first, then press '''1''.) The selected tine
of ''7:00'' appears and immediately the display changes to: —
Then, press "t" to select the "AM" setting. (Press "2 to
select the "PM" setting.) Then, the following display appears.
Press 4" and 2" for specifying "CHANNEL
12".
SEt CHANNEL HO ~—
-14—
Now the following display appears on the screen to show the
ON TIMER
is set to "7:00 AM, CHANNEL
12" with the
< YES >. indicating the ON
TIMER
has started. Finally,
press POWER button
@ to turn the power off. POWER/
ON TIMER indicator @ remains lit to show that the ON
TIMER is in operation.
Notes:
© {fan invalid time is selected (for example: 17:70"), it will
be rejected and the ON TIMER must be reset properly.
@ First select the broadcast mode (CHANNEL or CABLE) of
the channel you wish to set for the ON TIMER with ANT/
CABLE button
@ on the Remote Control before entering
the ON TIMER mode, since broadcast mode switching while
in the ON TIMER will cancel the mode.
© After the ON TIMER has been properly set, it functions only .
once for each setting {up to 2 settings are possible) to turn
on the TV's power. (it does not operate repeatedly every day
at the same time as a serial timer.)
© Once the ON TIMER turns the TV on automatically, if the
TV is not operated in any way, after 2 hours the TV will
turn off automatically for safety. A single adjustment, even
audio level adjustment or channel selection, will cancel this
switch-off function.
@ While the ON TIMER is activated, if the power is disconnect:
ed (such as in the case of power failure, etc.) and reapplied
later, the ON TIMER
is cancelled. When disconnected only
for a couple
of minutes,
the ON
TIMER
is reactivated;
however, it turns the TV on later than the set time by the
amount of time of interruption.
@ If the channel which has already been set as a "Guarded
Channel"
is selected, that channel is rejected and cannot be
set for the ON TIMER. (For details of the Guarded Channels,
refer to page 17.)
6, SET CLOCK
Your TV has a built-in clock. Set the clock as follows.
1) With "PAGE-2" (or "PAGE-1" or "PAGE-3"} MENU dis-
played on the screen, press "6" of 10-Digit Keypad @-. The
display will show:
2) Then, press the numbers (be sure to key in 4 digits) on the
10-Digit Keypad to set the current time. For example, if the
present time is 7:35 PM, press, ''7'', '3°' and '5'. Then, the
display changes to:
3) Press "2" to select the "PM" setting. (Press ''t" to select the
"AM" setting.) Then, the display changes to the following to
show the current time is set and the clock starts operating,
Notes:
.
®
(fan invalid time is selected (for example: 17:70"), it will
be rejected and the built-in clock must be reset properly,
@
if you wish to set the clock precisely, in step 3) above, press
"2" {or 1") at the same instant of a time signal.
@ The built-in clock may loose, time depending on the manner
in which the TV is used or the frequency of the power source.
If the time difference becomes great, re-adjust the clock.
®
If the power is disconnected (such as in the case of a power
failure, etc.), and reapplied later, the clock will stop operat-
ing. {The clock status can be checked on screen. Press the
DISPLAY
button.
!f the clock has stopped, the message
"CLOCK STOPPED" is displayed instead of the current time.
See 'DISPLAY
Button' on page 21 for details.) When dis-
connected
only for a couple of minutes, the clock is re-
activated; however, it will be later than the actual time by
the amount of time of interruption.
-15—
S09Ze-AV
S05Z2-AV
Advertisement
