Advertisement
Four-channel mode (Fig. 25)
[2]
RCA Input Seiect Switch
For two-channel input, slide this switch
to the left. For four-channel input, slide
this switch to the right.
[13} Output (Front/Rear)
if only one input pin plug is used, do not
connect anything to RCA input jack B.
[14] White
{15] Red
{16] Connecting wires with RCA pin plugs
{sold separately)
{20) Speaker out B: Speaker (right)
{21} Speaker out B: Speaker (left)
[22] Speaker out A: Speaker (left)
{23] Speaker out A: Speaker (right)
{24} Black cover
[25] Black stripe
{26] Green cover
[27] Green stripe
[28] RCA input pin jack A
[29] RCA input pin jack B
* Connect the front or rear output pin plugs
to jacks [28] or [29], according to your
system.
{30] if only one input pin plug is used, do not
connect anything to RCA input jack B.
GM-X404,x304
Three-channel mode (Fig. 26)
[2]
RCA input Select Switch
For two-channel input, slide this switch
to the left. For four-channel input, slide
this switch to the right.
[13] Output (Front/Rear)
If only one input pin plug is used, do not
connect anything to RCA input jack B.
{14] White
[15] Red
[16] Connecting wires with RCA pin piugs
(sold separately)
[20] Speaker out B: Speaker (right)
[21] Speaker out B: Speaker (left)
[24) Black cover
[25] Black stripe
[26] Green cover
(27] Green stripe
[28] RCA input pin jack A
[29] RCA input pin jack B
* Connect the front or rear output pin plugs
to jacks [28] or [29], according to your
system.
[30] If only one input pin plug is used, do not
connect anything to RCA input jack B.
{31] No connection
{32] Speaker out A: Speaker (mono!
{16]
Fig. 27
{13]
Two-channel mode (stereo) (Fig. 27}
{2]
RCA Input Select Switch
Slide this switch to the left.
[13] Output
[14] White
[15] Red
[16] Connecting wires with RCA pin plugs
(sold separately)
{24] Black cover
{25] Black stripe
{26] Green cover
[27] Green stripe
[28] RCA input pin jack A
[31] No connection
[33] Speaker (right)
[34] Speaker (left)
Two-channel mode (mono) (Fig. 28)
[2]
RCA Input Select Switch
Slide this switch to the left.
{13) Output
(14] White
[15] Red
[16] Connecting wires with RCA pin plugs
(sold separately)
[24] Black cover
[25] Black stripe
[26] Green cover
[27] Green stripe
[28] RCA input pin jack A
[31] No connection
[35] Speaker (mono)
Installation
QS CAUTION
* Do not install in:
— Places where it could injure the driver
or passengers if the vehicle stops
suddenly.
— Places where it may interferewith the
driver, such as on the floor infront of
the driver's seat.
Make sure that wires are not caught in the
sliding mechanism of the seats, re sulting
in a short-circuit.
Confirm that no parts are behind the
panel when drilling a hole for installation
of the amplifier. Protect all cables and
important equipment such as fue! lines,
brake lines and the electrical wiing from
damage.
Install tapping screws in such away that
the screw tip does not touch any wire.
This is important to prevent wins from
being cut by vibration of the car, which
can result in fire.
To ensure proper installation, ue the
supplied parts in the manner spic éfied. If
any parts other than the suppliel ones
are used, they may damage inten al parts
of the amplifier, or they may beiorne
loose causing the amplifier maysFaut
down.
23
lpi aS an i N g t w p
Advertisement
