Table of Contents
Advertisement
Available languages
Available languages
e@
TAPE MONITOR
When a cassette deck with a monitor function (a 3-head system)
is used for recording, pressing TAPE
MONITOR
switch 1 (or 2)
allows you to monitor recording conditions through the speakers.
Make
sure that the recording and
playback
cables are both con-
nected at this time.
Note: With a 2-head tape deck, recordings cannot be monitored
with the TAPE MONITOR
switch.
However, you can listen
to the sound from the program source.
e
DUBBING RECORDED TAPES
If you have two cassette decks, you can dub selections previously
recorded
from
FM
broadcasts or the like to another tape.
It is
also possible to dub from open reel tape to cassette tape.
1. Connect two tape decks,
2. When dubbing from
tape deck
1 to tape deck 2, press TAPE
COPY
2; when
dubbing
from
tape deck
2 to tape deck
1,
press TAPE COPY 1.
Notes:
1. To monitor a selection while it is being recorded, press TAPE
MONITOR
switch
1 or 2, depending
on which deck is being
used as the source.
2.
It is also possible to listen to another program
source while
dubbing
tapes.
In this case, make sure that TAPE
MONITOR
switches 1 and 2 are OFF.
SPECIAL
FUNCTION
Combining the SD530, SD630 or SD430 with the Marantz PM630
or PM730 amplifier, ST530 tuner and other equipment allow you
to build aconvenient system as shown below.
@
Easy Operation Bus System
When
the PM630 or PM730 are connected to the SD530, SD630
or SD430,
ST530,
TT333
and the remote contro! receiver, the
source
selector
of the
PM630
or
PM730
are
automatically
switched only by operating the PLAY
button of the equipment
played.
The amplifier and other equipment
must be connected together
using the easy operation bus cables (with green plugs).
The
£.0. bus output terminal
of an equipment
should
be con-
nected
to the E.Q. bus input terminal of an equipment which is
closer to the amplifier.
Notes:
1. The
easy
operation
bus
of the
SD530,
SD630
or
SD430
cannot be used during recording.
2.
The
easy
operation
bus
of the
SD530,
SD630
or SD430
functions
only when
the input and
output
cables are con-
nected to the TAPE
1/VIDEO terminals; it does not function
when they are connected to the TAPE 2/EQ terminals.
Example of connection:
See Figure 3.
©
Remote Control (R.C.) Bus System
Plug
the remote
control
cable
(orange)
into this terminal
and
into the corresponding terminal on the tuner, cassette deck, etc.
Be
sure to connect the cable to the connector
with the orange
marking;
connecting
it to
any
other
connector
can
result
in
damage to your equipment. The remote control bus carries signals
sent
to the remote control
receiver
by infrared
pulses from the
remote
control
unit
(whose
amplifier
section
memory
contains
volume
control, function
switching, muting
and
loudness opera-
tions)
making
it possible to operate
the main
unit by remote
control.
Example of connection:
See Figure 3.
@® INPUT SELECTOR
® ELECTRONIC VOLUME (UP/DOWN)
MUTING
TAPE 1/VIDEO
TAPE 2/EQ
LOUDNESS
BALANCE
(L/R)
HiGH/SUBSONIC FILTERS
288889
*
RMC-12 remote control unit
Controlled by infrared pulse signal.
IN CASE
OF DIFFICULTY
Only
the most
competent
and
qualified
technicians
should
be
allowed
to
service
your
amplifier.
The
Marantz
company
and
its factory trained service personnel have the knowledge and the
necessary
equipment
needed
for repair and
calibration
of this
precision instrument.
In the event of difficulty refer to your dealer or write to one of
the locations listed at the end of this manual
for the name and
address of the Marantz
service station nearest your hone. Please
include the model and serial number of your unit together with
a description of what you feel is abnormal in its behaviour.
REPACKING
FOR SHIPMENT
elsewhere, please observe the following precautions:
a.
Pack the unit carefully, using the original material as shown in
Figure 10.
b. Ship via a reputable carrier (do not use Parcel Post) ard obtain
a shipping receipt from the carrier.
Advertisement
Table of Contents
