DeWalt DWV905M Manual page 12

EnglisH
DWV9220
DWV9470
Vac Rack Installation (Fig. O)
1. Remove the 4 carry handle screws
and remove the carry handle.
2. Install the vac rack reusing the carry handle screws. Put
them back in their original holes and tighten.
3. Use the 2 screws 37 provided by placing them in the rear
holes of the vac rack. Push down and turn each screw to
break through the material and into the hidden screw boss
below. Tighten.

CAUTION: Do not exceed 9 kg (30kg for model DWV9510)
in each 14 liter storage unit, maximum 2 storage units
per dust extractor. Do not exceed 18 kg in a 28 liter
storage unit, 1 storage unit per dust extractor. Exceeding
the recommended height and/or weight could result
in an unstable dust extractor would could cause injury
or damage. For model DWV9510, the recommended
height is 40 cm.

CAUTION: Do not carry the dust extractor at the handles
of the mounted storage units.
NOTICE: Do not remove dust extractor head from tank
with T‑stack storage units attached. Doing so could result
in damage to the dust extractor filter.
NOTICE: The carry handle should be stored for possible
dismantling.
If the rack is to be removed again, this is done in reverse order.
The handle must be refitted and the two rear screws must
be screwed back into the motor head enclosure, to close the
screw holes.
Securing the Power Cord to the Hose
(Fig. A)
The power cord 2 can be secured to the suction hose
using the D279058CL hose clip (available from your local
D WALT supplier).
e
Consult your dealer for further information on the
appropriate accessories.
Troubleshooting
Problem Solution
Motor does Check power cord, plugs and outlet.
not run
Ensure the on/off /tool control switch is in the
ON position ).
10
Woodworking Kit
(DWV9000 + DWV9130
x 3 + DWV9120 +
DWV9150 + Cable
Hose Clip)
Y Splitter Hose Kit
36 using a T-25 star bit
Problem
Suction
capacity
decreases
Vacuum
stops
running
Dust comes
out while
vacuuming
Automatic
filter
cleaning is
not working
Dust
extractor is
not turned
on by
Wireless Tool
Control™
7
equipped
power tool
or remote.
Solution
Remove blockages in the suction nozzle,
suction tube, suction hose or filters.
Replace the paper or fleece bag.
Check for proper installation of the filters.
Clean or replace the filters.
Empty canister, refer to Empty Canister
under Operation.
Thermal overload has been tripped:
1. Turn the vacuum off and disconnect
vacuum cleaner from power source.
2. Empty the canister, if needed.
3. Allow the unit to cool.
4. Plug the power cord into an appropriate
outlet and turn on/off/tool control switch
to the ON position ) to test. If vacuum will
not restart contact your seller or check the
location of your nearest authorised D
repair agent in the D WALT catalogue or
e
contact your D WALT office at the address
e
indicated in this manual.
Check for proper installation of the filters.
Ensure filters are not damaged; replace
if necessary.
Ensure filter seals are in place and are secure.
Listen for the solenoid clicking to ensure the
filter cleaning mechanism is working.
1. Move the on/off tool control switch
Wireless Tool Control™ mode . Confirm
LED is illuminated. If LED is not illuminated
with the selector in Wireless Tool Control™
mode, contact D WALT service centre.
e
2. Remote/power tool is not paired to dust
extractor. Follow pairing steps.
3. Remote/power tool is out of range of dust
extractor. Move dust extractor closer to
remote/power tool.
4. Wireless Tool Control™ remote coin cell is
dead. Replace coin cell and retry.
5. Ensure paired tool's battery is fully charged
and fully inserted.
6. If tank is full of liquid and sense circuit is
tripped:
a. Turn the on/off tool control switch to
the Off (0) position and disconnect from
power source.
b. Empty tank.
WALT
e
14 to