Table of Contents
Advertisement
NOTES:
• Do not adjust the horizontal louvers by hand.
• In the Auto or Heating mode, the airflow direction stay position 1 for
a while from the start of the operation.
• In the Cooling or Dry mode, position 1-3 is recommended to prevent
condensation drips damaging your property. If position 4-6 keeps for
30 minutes or more in these modes, the airflow direction changes to
position 3 automatically.
• When using the mobile app (optional WLAN adapter is necessary),
the up/down airflow can be selected from 4 positions.
6. TIMER OPERATIONS
NOTE: When [
] indicator on the indoor unit blinks, set the clock and
timer again. This blinking shows that the internal clock go wrong
due to an interruption of the power supply.
■ Timer setting procedure
1. Press
to choose timer operation.
Each time you press the button, the timer operation will
change as follows:
Off timer
On timer
Program timer
To cancel the timer setting during the procedure, press
•
.
To set sleep timer, press
•
timer".)
2. Set each timer operation.
For details, refer to the following instructions of each timer setting.
6.1. On timer or Off timer
1. Select On timer or Off timer in step 1 of "Timer setting
procedure".
2. Each time you press
as follows:
0.5
1.0
1.5
2.0
• When you use the On timer, set the time while the
the remote controller display is blinking.
• When you use the Off timer, set the time while the
the remote controller display is blinking.
• To deactivate the On/Off timer, press
[
] is shown on the remote controller display. The indicator will
disappear.
NOTE:
• If you set the Sleep timer after setting the On/Off timer, the
On/Off timer is canceled.
6.2. Program timer
1. Set On timer and Off timer. (Refer to "6.1. On timer or Off
timer".)
2. Select Program timer in step 1 of "Timer setting procedure".
After the time set by the earlier timer passed, the timer set later will
begin the counting down.
The order of the timer operation is displayed as follows:
Stops the operation at your desired
time.
Starts the operation at your desired
time.
Operates as the combination of the
On timer and Off timer.
. (Refer to "6.3. Sleep
, the time changes
...
9.5
10
11
12
hours
indicator on
indicator on
while [
] or
Timer
Indicator on the remote controller display
Off→On timer
On→Off timer
NOTE: If you set the Sleep timer after setting the Program timer, the
Program timer is canceled.
6.3. Sleep timer
The Sleep timer supports your comfortable sleep by moderating the air
conditioner operation gradually.
Press
.
)
Each time you press the button, the time changes as follows:
0.5
1.0
2.0
To repeat the timer, press the button when
displayed.
During the Sleep timer operation, the setting temperature changes as
the following figure.
In Heating mode
1 °C
2 °C
3 °C
30 min
1 h
1.5 h
Set time
After the set time has elapsed, the air conditioner operation turns off.
7. ENERGY SAVING OPERATION
7.1. Economy operation
It saves more electricity than other operation modes by changing the set
temperature to a moderate setting.
Press
to activate/deactivate the Economy operation.
)
[
] indicator on the indoor unit will turn on.
NOTES:
• In the Cooling, Heating, or Dry mode, the maximum output of this
operation is approximately 70 % of usual operation.
• This operation cannot be performed during the temperature
monitoring by the Auto mode.
7.2. Fan control for energy saving
In the Cooling operation, when the room temperature
reaches the set temperature, the indoor unit fan
rotates intermittently to save the power. (This function
is activated at the time of purchase.)
To change the setting, use the following steps;
1. Press
until the indicators on the remote controller turn off.
2. Press and hold
The
and the current status will appear.
: Activated
: Deactivated
3. Press
4. Press
to send the setting to the indoor unit.
The display will return to the original screen.
NOTE:
• If you do not press any buttons for 30 seconds after
will turn off. In this case, repeat the setting from step 2.
En-5
3.0
5.0
7.0
CANCEL
indicator is not
In Cooling or Dry mode
4 °C
Set time
Set
1 h
temperature
1 °C
for more than 5 seconds.
to switch the status.
9.0
hours
2 °C
is displayed,
Advertisement
Table of Contents
