JVC GR-DVL100U Manual page 13

24
a RECORDING Advanced Features (cont.)
Menu Screen Explanations (cont.)
CAMERA MENU
Demonstrates certain functions such as Program AE with special effects, etc.,
and can be used to confirm how these functions operate. When "DEMO.
MODE" is set to "ON" and the Menu Screen is closed, demonstration starts.
Performing any operation during the demonstration stops the demonstration
temporarily. If no operation is performed for more than 1 minute after that,
the demonstration will resume.
NOTES:
@ Ifa tape is in the camcorder, the demonstration cannot be turned on.
© "DEMO. MODE" remains "ON" even if the camcorder power is turned off.
© If "DEMO. MODE" remains "ON", some functions will not be available.
After viewing demo, set to "OFF".
'Automatic demonstration will not take place.
The Side LED indicator (7 pg. 62, 63) lights on the camcorder when using.
the AC Power Adapter/Charger as a power supply unit, and lights for approx.
5 seconds when using the battery pack. The Power Switch should be set to
" B Y on".
TELE |ON
MACRO
MANUAL MENU
WIDE
MODE
To compensate for unstable images caused by camera-shake, particularly at
high magnification.
NOTES:
'© Accurate stabilization may not be possible if hand shake is excessive, or
under the following conditions:
'*When shooting subjects with vertical or horizontal stripes.
'*When shooting dark or dim subjects.
'* When shooting subjects with excessive backlighting.
When shooting scenes with movement in various directions.
'*When shooting scenes with low-contrast backgrounds.
Switch off this mode when recording with the camcorder on a tripod.
@ The "C¥»" indicator blinks or goes out if the Stabilizer cannot be used
Usually the distance to a subject where the lens is in focus depends on the
zoom magnification. Unless there is a distance more than 1m (3.3 ft) to the
subject, the lens is out of focus at the maximum telephoto selting. When set
to "ON", you can shoot a subject as large as possible at a distance of approx.
60 cm (2 ft).
+ Depending on the zoom position, the lens may go out of focus.
Records with no change in the screen ratio. For playback on a TV with a
normal screen ratio.
CINEMA
Inserts black bands at the top and botiom of the screen. During playback on
wide-screen TVs, the black bands at the top and bottom of the screen are cut
and the screen ratio becomes 16:9. [] appears. When using this mode, refer
to your wide-screen TV's instruction manual. During playbach/recording on
4:3 TV¥LCD monitor/viewfinder, black bands are inserted at the top and
bottom of the screen and the image appears like a letterboxed 16:9 movie.
'SQUEEZE
EEG : Factory-preset
For playback on TVs with an aspect ratio of 16:9. Naturally expands the image
to fit the screen without distortion. [HZ] appears. When using this mode, refer to
your wide-screen TV's instruction manual. During playback/recording on 4:3,
'TVS/LCD monitor/viewsinder, the image is elongated vertically.
en2o
Helps cut down on noise created by wind. " @S" appears. The quality of the
sound will change. This is normal.
Disengages the function which cuts down on noise created by wind.
Does not reset all settings to the factory-preset.
3] winn [ON
| cur
3
Es CAM
g | RESET execute
'ON ep
SCREEN
'Keeps the camcorder's display (except the date, time and time code) from
Resets all settings to the factory-preset.
appearing on the connected TV screen.
eae
H | Makes the camcorder's display appear on screen when the camcorder is
connected to a TV.
Keeps the indications (except the tape running indicator, warnings, date, time,
time code, etc.) from appearing in the camcorder. Also keeps the camcorder's
display (except the date, time and time code) from appearing on the con-
nected TV screen.
The date/time is always displayed.
The date/time does not appear.
Time code is displayed on the camcorder and on the connected TV. Frame
numbers are not displayed during recording.
Time code is not displayed.
> 'SIMPLE
g
=
z
a
a|TIME Orr
Ewe [on
CODE
CLOCK
ADu.
EEE : Factory-preset
NOTES:
'Allows you to set the current date and time (CF pg. 11).
© The "MANUAL MENU" settings are effective only when the Power Switch is set to".
© "DISPLAY MENU" functions which are set when the Power Switch is set to "(i)" are also applied when the
Power Switch is set to "EMI" ( pg. 32). "CLOCK AD)." only appears when the Power Switch is set to
© The "DISPLAY MENU" settings are effective even when the Power Switch is set to "EN".
© The "ON SCREEN" setting can also be changed by pressing the DISPLAY Button on the remote control
(provided) (1 pg. 35, 38, 45).