Denon UPO-250 Operating Instructions Manual page 20

'\) fi] REMOTE CONTROL UNIT
a;
The 0-250 is supplied with a remote contro! unit (RC-184) for
system control.
Replace the batteries with new ones when the transmission
distence possible with the remote control unit shortens.
For tonger battery life, remove the batteries when not using
the remote control unit for long periods.
When replacing batteries, use two new batteries. Never use
an old battery with a new one.
Do not use two different types of batteries.
Do not heat batt or take them. apart.
Be careful that the remote contro! sensor is not exposed to
direct sunlight or strong light from lighting fixtures.
The remote contro! sensor is focated on the tuner preampli-
fier. Point the remote control unit at the sensor, then press
the buttons for the desired operation.
Operate the remote controt unit within the range ifjustrated
in the diagram.
Remote contro! sensor
30°
Remote contros unit's
transmission window
@ Open the battery case lid on the back of the remote contro}
unit.
@insert the two batteries (REP, AA)
in the proper direction.
cc «appears at the upper left corner of the
tuner-preamplifier's display when a signal is
received.
© The remote control unit can be used at a
distance of about 7 meters from the remote
control sensor, but this distance will be
shorter if there are obstacles in the way or if
the remote control is operated from an
angle.
10. Do not press buttons on tha remote contro! unit and on the main unit at the same time. Doing so will lead to a malfunction.
11.
\t EERE appears on the tuner-preamplifier's display due to incident light even though the remote contro! unit has not been
operated, it is best to move the set or place it in a different direction. Even if this happens, it will not cause a malfunction with remote
control unit.
When adjusting the volume continuously with the remote controt unit, the volume adjustment will stop if the remote control unit is
moved away from the remote control sensor. Should this happen, press the button again to continue changing the volume.
SLEEP
Press this to set the sleep timer.
Press this to switch on the power for the
entire system or set the system to
standby.
TUNER
Press this to listen to the preset stations.
CD Play
DIRECT button
Press for direct track selection of CD
pleyer,
PROGRAM button
Press for programmed selection of CD
player.
CANCEL button
Press once during programming to can-
cel the tast track programmed.
CENTER and REAR jevel
Use to adjust the volume of an optional
AV amplifier. Press Ww to lower the
volume, 4 to raise the volume.
Operating the CD Player
Pause button (tl)
Press to temporarily stop CD play. Press
the play button Db to resume play.
Stop button ( @ }
Press to stop CD play.
Play button (>}
Press to start CD play.'
Manual search backward button (44)
Manual! search forward button (PP)
Press these to quickly move backward or
forward.
Backward skip monitor button (44)
Press during CD play to go back to the
beginning of that track. Press the button
again within 0.5 seconds to go back to the
beginning of the previous track.
Forward skip monitor button (>>I)
Press during CO play to go forward to the
beginning of the next track. Press the
button again to go forward to the begin-
ning of the track two tracks ahead.
Button Names and Functions
SDB {Super Dynamic Bass)
Press this button for more powerful
bass sound. Press again to return to
the original setting.
When the MAIN/AV switch is set to the AV side, number buttons 4, 5, 6, and +10
can be used for the following operations. Use these buttons when a DENON AV
amplifier having these functions is used with this system.
4 button -+ VCR-2
5 button —- 08S
6 button ~ TV
+10 button -- 3CH LOGIC
MAIN/AV switch
Switch to the AV side when the system is
used together with the optional AV ampli-
tier. Usually, this switch is set to the
MAIN side. When set to AV, the number
buttons switch over to the functions indi-
cated below them.
FUNCTION {input switching) button
Switches the function between TUNER,
TAPE, CO, PHONO, and DAT.
Number buttons
After pressing TUNER, these buttons call
up the preset stations.
When used with CD piay, after pressing
DIRECT or PROGRAM, these buttons spe-
cify the tracks to be played.
MASTER VOLUME
Adjusts the volume.
Press V to tower the volume, and A to
raise it.
Operating the Cassette Decks
Deek 1/2 button
Press this to setect the deck to be oper-
ated.
Stop button ( M@ )
Press this to stop the tape deck.
Forward play button (>)
Press this to play back or record in the
forward direction.
Reverse play button (4)
Press this to play back or record in the
reverse direction.
@ REC/REC MUTEE button
(recording/recording mute button)
To set the recording mode when in the
stop mode. press this buttan, then press
either the "Db" or the "4° button. When
pressed during the recording or record-
ing pause mode, @ biank section of appro-
ximately § seconds is created on the tape,
after which the deck is set to the record-
ing pause mode.
Rewind button (44)
Press this to rewind the tape.
Fast-forward button (b>)
Press this to fast-forward the tape.
TAPE MONITOR button
Use this to monitor the sound of the tape.
When used in combination with a 3-head
deck, the recorded sound can be moni-
tored {from the tape).
G)
m
z
m
D
>
-
"
m
2)
=
Oo
z