Playing Cds - Denon UPO-250 Operating Instructions Manual

SL
@ Making a Synchro Dubbing (Copy)
Synchro dubbing (tape copying) can be made at regular speed from deck 1 to deck 2.
1 or as Prass the SYSTEM POWER button of the tuner-preamplifier.
@ Press the SYSTEM POWER button of the tuner-preamplifier or press the POWER ON/STANDBY button of the deck.
@ Press the OPEN/CLOSE (@&) button and toad the tape to be plsyed back in deck 1.
@ Press the OPEN/CLOSE (@) button and toad the tape to be recorded back in deck 2.
@ Set the reverse mode with the REV MODE switch.
{REV MODE <= Da:cqQ)
® Press the DUBBING (synchro dubbing) button. Note that if the POWER ON/STANDBY button of the deck is pressed to switch on the
power, the power of the tuner-preamplifier will automatically be switched on when the DUBBING button is pressed. You will be able to
hear the audio normally.
@To stop the dubbing, press the stop button ( MB) or press the DUBBING button.
The tape will automatically stop when it reaches the end and the synchro dubbing mode will be cancelled.
© Recording level during synchro dubbing
During synchro dubbing, the recording is made at the same level as the playback tape of deck 1, regardless of the position of the
recording level control. Note that when the recording tape and the playback tape are of different types, the recording level might be
different and so synchro dubbing should be done with the same type of tape if possible.
© Dolby NR mode during synchro dubbing
Tha Dolby NR system is automatically disengaged from the panel switch during synchro dubbing (even though the displey does not
change) and the tape is recorded with the Dolby NR mode of the playback tape.
¢ You cen listen to the sound of another source while synchro dubbing.
Changing the source with the FUNCTION button or the CD play button will not interrupt the synchro dubbing.
@ When synchro dubbing, both decks begin running in the forward direction (from the A side).
© The synchro DUBBING button is effective in starting the operation only when both tapes are in the stopped condition.
© The following buttons do not function during the synchro dubbing operation: forward play P, reverse play €, fast forward PP. rewind
4, and REC/REC MUTE.
e To ensure complete reproduction, use the same length of recording tape as the playback tape, and rewind both tapes to the beginning
of side A before starting the dubbing operation.
© By setting the REV MODE switch tothe = or C2 position, when the playback tape of deck 1 reverses at the end of the tape on
side A, the deck 2 tape will reverse at the same time and dubbing can continue on side B.
16
[11] PLAYING CDs
© Press the OPEN/CLOSE button (@) once to open the disc try, once again to close it.
© The disc tray can also be closed by pressing the play (>) button.
When this is done, playback automatically starts from the first track on the disc (or if the tracks are programmed, the first programmed
track).
@ Load the disc with the label side facing up, being careful not to touch the disc surface.
© Load the disc with the disc tray open all the way.
© Set the disc securely in the tray guide at the center of the disc tray.
To play an 8 cm diac, place the disc in the sunken part at the center of the disc tray.
@ When removing the disc trom its case:
As shown in the diagram, grasp the
disc along the edges, gently press
down on the hole in the middle
with a finger, and Jift the disc. {t
should come out easily.
PACT
( Only discs with this mark can be
played.
OIGITAL AUDIO
© For CDVs. only the audio part is played (the video part is not
played).
@ When setting the disc in the disc tray:
Always set the disc with the label
side facing up. (Compact discs can
onty be played on one side). For 8
cm CDs, set the disc in the sunken
part in the middle of the tray.
Handling the Disc Tray
Do not switch off the power or push or pull the disc tray when it is moving, since
this may damage it.
if the cord of a set of headphones, etc., gets caught in the disc tray when it is closed,
press the OPEN/CLOSE button (@&) again.
© Never set objects other than CDs in the disc tray, a8 this can cause damage.
NOTE:
| "NO DISC" is displayed on the display window when no disc is toaded,
when the disc is loaded upside-down, or when the disc is not properly
loaded. Also," OO, 00, ~ may appear during playback of a CD if the
disc 1s scratched or dirty. If this happens, the set will not operate when 3
normal operating button (other than the OPEN/CLOSE button) is pressed,
$o press the OPEN/CLOSE ( &) button, remove the disc, clean it as
necessary, then press the PLAY (>) button again.
wae A an Mm oscew
ca UUn ed,
922666 7 bo 80 55 17 19 86 os 88 87 OB 08
G)
m
z
m
a
>
a
n
mr
i?)
a4
O
Zz