Download Print this page
Stanley SL5HS Instruction Manual
Stanley SL5HS Instruction Manual

Stanley SL5HS Instruction Manual

2m lithium-ion led spotlight
Hide thumbs Also See for SL5HS:

Advertisement

Available languages

Available languages

Quick Links

x
2M LITHIUM-ION LED SPOTLIGHT
INSTRUCTION MANUAL
1
2
3
4
6
7
5
7
8
9
14
10
13
11
12
SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.
BC
Copyright © 2017
Baccus Global LLC, Boca Raton, FL 33432
(877) 571-2391
Optional 120V AC/USB Charging Adapter: This device complies with part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not approved by the party responsible for compliance could void user's authority
to operate the equipment.
SAFETY GUIDELINES / DEFINITIONS
DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates potentially hazardous situation
which, if not avoided, may result in property damage.
RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety precautions
should always be followed to reduce the risk of personal injury. Improper operation,
maintenance or modification of tools or equipment could result in serious injury and
property damage. There are certain applications for which tools and equipment are
designed. Manufacturer strongly recommends that this product NOT be modified and/or
used for any application other than for which it was designed. Read and understand all
warnings and operating instructions before using any tool or equipment.
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS
WARNING: Read all instructions before operating the spotlight. Failure to
follow all instructions listed below may result in electric shock, fire and/or
serious injury.
GENERAL SAFETY WARNINGS AND INSTRUCTIONS
WARNING: This product or its power cord contains lead, a chemical known to the
State of California to cause cancer and birth defect or other reproductive harm. Wash
hands after handling.
INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS
WARNING: RISK OF FIRE, ELECTRIC SHOCK, BURST HAZARD, OR INJURY TO
PERSONS – WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:
• LED gets HOT quickly!
• Do not touch the LED at any time when operating.
• Only contact trigger when turning on.
• Do not touch hot lens or enclosure.
• Do not remain in light if skin feels warm.
• Do not operate the spotlight with a missing or damaged lens or enclosure.
WARNING – WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:
• The spotlight and the supplied charging adapters are not toys and cannot be played
with as toys. To reduce the risk of injury, close supervision is necessary when these units
are used near children.
• Use only attachments recommended or sold by the manufacturer.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK:
• Do not put the spotlight in water or other liquid. Do not place or store this light
where it can fall or be pulled into water or become wet.
• Charge indoors only. Do not expose charger to water or any other liquid.
• Do not clean this appliance with a water spray or the like.
• Use only the chargers supplied by the manufacturer to charge and recharge.
• When an extension cord is used:
– The marked rating of the detachable power supply cord or extension cord should
be at least as great as the electrical rating of this appliance.
– The cord should be arranged so that it will not drape over the countertop or
tabletop where it can be tripped over, snagged, or pulled on unintentionally
(especially by children).
– The extension cord should be kept dry and off the ground.
WARNING: FIRE HAZARD:
• Never contact combustible material to the lens.
• Keep spotlight lamp away from materials that may burn.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• All lights give off heat:
– Do not touch lens while operating.
SL5HS_ManualENSP_072617.indd 2
SL5HS
– Keep combustibles away from spotlight lens. Extreme heat can cause fires.
– Never place the light face down on any surface when lit, charging or not in use.
Never store the light face down on any surface.
• Never look directly into the light or shine the light into another person's eyes.
• Keep sharp objects away from lens — it is glass and can break.
• Do not immerse spotlight in water.
• Do not expose this unit to extremely high temperatures.
• Do not drop or throw spotlight. It contains glass and a lithium-ion battery.
• Use only with either the AC or DC charging adapter and USB charging cable that are
provided with unit. Plug in the charging cable at the light first, then plug into the
charging source.
• After charging/recharging, disconnect charging adapter or extension cord and wait 5
minutes before use.
• Do not crush, cut, pull or expose charging adapter cords to extreme heat.
• Position charging adapter cords so they do not become entangled or become a safety
hazard. Keep charging adapter cords away from sharp edges.
• Use in a dry location only.
• There are no user-serviceable parts inside. Do not attempt to disassemble any other
parts of the unit.
• To reduce risk of damage to electric plug and cord, pull by plug rather than cord when
disconnecting.
• Do not attempt to charge the unit if the charger or cord is damaged – return the
charger to manufacturer for repair or replacement.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM-ION BATTERIES
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, BURST HAZARD,
OR INJURY TO PERSONS OR PROPERTY:
Lithium-ion batteries are small, compact and ideal for providing long-lasting power to
this unit. However, they must be used and charged properly. Improper use can result in
serious injury, fire, or death.
• Lithium-ion batteries can explode in the presence of a source of ignition. Do not use
the product in the presence of an open flame.
• Do not place this lithium-ion battery powered unit in fire or apply heat to it.
• Do not subject this lithium-ion battery powered unit to strong impacts or shocks. The
battery in this unit contains safety and protection devices which, if damaged, may
cause the battery to generate heat, rupture or ignite.
• Do not expose this lithium-ion battery powered unit to water or salt water, or allow
the battery to get wet.
• Avoid storing this lithium-ion battery powered unit in the basement, bathroom or
other areas of the house that are or may become wet or humid or where moisture
may concentrate.
• Do not leave this lithium-ion battery powered unit in direct sunlight, or use or store
the unit inside cars in hot weather. Doing so may cause the battery to generate
heat, rupture, or ignite. Using the battery in this manner may also result in a loss of
performance and a shortened life expectancy.
• Never charge this unit near heat or flammable objects.
• NEVER THROW WATER ON A BURNING LI-ION BATTERY! If a lithium-ion battery
does catch on fire, it will burn even more violently if it comes in contact with
water or even moisture in the air. A fire extinguisher must be used.
Battery Charging and Capacity
This unit is delivered in a partially charged state – you must fully charge it before using
it for the first time.
When stored at room temperature with a full charge, Li-ion batteries will will begin to
discharge from the time they are manufactured, even when unused. Deep discharges
also decrease their capacity. Battery life can be extended by the following:
• Charge battery to full capacity before storage.
• Optimal storage temperature for this unit is between 5°C and 20°C (41°F and 68°F).
• Never discharge the battery fully.
• Charge after each use.
• Always charge at least once every 3-6 months if not in frequent use to prevent
overdischarge.
Transportation of Lithium-Ion Batteries
• Always check all applicable local, national, and international regulations before
transporting a unit containing a Lithium-Ion battery.
• Transporting an end-of-life, damaged, or recalled battery may, in certain cases, be
specifically limited or prohibited.
INSTRUCTIONS PERTAINING TO THE 12V DC/USB CHARGING
ADAPTER
CAUTION: TO AVOID THE RISK OF PROPERTY DAMAGE:
• NEVER CONNECT THE UNIT TO A POSITIVE GROUNDED VEHICLE.
• The 12 Volt DC charging adapter must only be connected to batteries with a nominal
output voltage of 12 volts. The unit will not operate from a 6 volt battery and will
sustain permanent damage if connected to a 24 volt battery.
• Always connect the 12 volt DC/USB charging adapter to the 12 volt DC power source
before plugging any devices into it
INSTRUCTIONS PERTAINING TO THE USB PORTS
• IMPORTANT: Some household USB-powered electronics will not operate with the USB
ports provided with this device. Check the manual of the corresponding electronic
device to confirm that it can be used with this type of USB port.
• The USB ports do not support data communication. They only provide power
to an external USB powered device (5V DC/2.1A using the USB port on the DC /USB
charging adapter or 5V DC/1A using the AC/USB charging adapter). Make sure the
rating of equipment plugged into the USB port does not exceed the amperage stated.
• Always connect the appropriate charging adapter to either the 120 volt AC or 12 volt
DC power source before plugging any devices into it.
• Do not attach USB hubs allowing connection of multiple personal electronic devices to
any of the USB ports on the charging adapters.
SAVE THESE INSTRUCTIONS
INTRODUCTION
Congratulations on purchasing your new Stanley 2M Lithium-Ion LED Spotlight.
Read this Instruction Manual and follow the instructions carefully before using
your new spotlight.
FEATURES
1. Swing-up Stand
2. 5-Position On/Off Trigger (Full/High/Low/Halo/Off)
3. Pistol Grip Handle
4. Area Lights (total of 8 around the Lens)
5. Main Beam LED
6. Battery/Charge Status LED Indicator
7. Micro-USB charging port (for use with the USB Charging Cable and Charging
Adapters)
8. USB charging cable (for use with 12V DC/USB Charging Adapter and 120V AC/USB
Charging Adapter)
9. Regular USB plug
10. Micro-USB plug
11. 12V DC/USB Charging Adapter (Optional Accessory)
12. 12V DC/USB Charging Adapter LED Indicator
13. 12V DC/USB Charging Adapter USB Port (Optional Accessory)
14. 120V AC/USB Charging Adapter (Optional Accessory)
15. 120V AC/USB Charging Adapter USB Port (Optional Accessory)
READING THE BATTERY/CHARGE STATUS LED INDICATOR
The battery and charging status LED indicator is located on the back of the unit. It lights
or flashes in three colors to indicate the following:
When charging:
Green: Battery is in a fully charged state.
Green (flashing): Battery is in a high partially charged state.
Orange (flashing): Battery is in a low partially charged state.
Red (flashing): Battery needs to be recharged.
Red (flashing rapidly): The battery of the unit is overheated due to extensive use or
recharging. The charging process will stop at this stage and will automatically resume
after a cool down period.
When operating:
Green: Battery is operating at full voltage.
Orange: Battery is operating at partial voltage.
Red: Battery is operating at low voltage, and should be recharged or the built-in low
voltage protection will be activated and the unit will automatically shut down shortly.
Red (flashing rapidly): The battery of the unit is overheated (due to extensive use
or recharging), or is too cold (the ambient temperature has dropped below -20°C).
Operation will stop at this stage.
CHARGING/RECHARGING THE SPOTLIGHT
This unit is shipped in a partially charged state. Charge unit after purchase and BEFORE
first use until the battery/charge status LED indicator lights green.
Recharge after each use until the battery/charge status LED indicator lights green.
IMPORTANT: When the unit is not in use, we recommend that the battery is
charged at least every 3 to 6 months.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• Never place the light face down on any surface when charging.
• Failure to keep the battery charged will cause permanent damage and result in poor
performance.
Charging/recharging using the 12V DC/USB Charging Adapter
1. Make sure the spotlight is off.
2. Insert the micro-USB plug of the USB charging cable into the micro-USB charging
port on the back of the spotlight.
3. Insert the regular USB plug of the USB charging cable into the 12V DC/USB charging
adapter.
4. Insert the 12 volt DC/USB charging adapter into the 12 volt DC accessory outlet of
a vehicle or other functioning 12 volt DC power source. The LED indicator on the
12V DC/USB charging adapter will light green when it is properly plugged into the
12 volt DC power source. The battery/charge status LED indicator will light or flash
in one of three colors (as described in the "Reading the Battery/Charge Status LED
Indicator" section) to indicate the charging status.
Note:
Some vehicles require that the ignition be switched to the accessory position
in order to power the accessory outlet.
5. Charge until the battery/charge status LED indicator lights green.
6. When charging is complete, first unplug the 12V DC/USB charging adapter from the
12 volt DC power source, then disconnect the USB charging cable from the adapter
and the spotlight. Store the adapter and cable in a safe place.
Charging/recharging using the 120V AC/USB Charging Adapter
1. Make sure the spotlight is off.
2. Insert the micro-USB plug of the USB charging cable into the micro-USB charging
port on the back of the spotlight.
3. Insert the regular USB plug of the USB charging cable into the 120V AC/USB
charging adapter.
4. Plug the 120V AC/USB charging adapter into a (powered) standard North American
120 volt 60Hz outlet. The battery/charge status LED indicator will light or flash in
one of three colors (as described in the "Reading the Battery/Charge Status LED
Indicator" section) to indicate the charging status.
5. Charge up to 5 hours or until the battery/charge status LED indicator lights green.
6. When charging is complete, first unplug the 120V AC/USB charging adapter from
the power source, then disconnect the USB charging cable from the adapter and the
spotlight. Store the adapter and cable in a safe place.
Charging/recharging using the USB charging cable and a device with a
USB power port (not supplied)
1. Make sure the spotlight is off.
2. Insert the micro-USB plug of the USB charging cable into the micro USB charging
port on the back of spotlight.
3. Insert the regular USB plug of the USB charging cable into a device's functional
USB power port. The battery/charge status LED indicator will light or flash in one of
three colours (as described in the "Reading the Battery/Charge Status LED Indicator"
section) to indicate the charging status.
4. Charge until the battery/charge status LED indicator lights green.
5. When charging is complete, disconnect the USB charging cable from the device's
USB power port and the spotlight. Store the cable in a safe place.
OPERATING THE SPOTLIGHT
The 5-Position On/Off Trigger turns the unit on and off, and is also used to choose the
following modes:
FULL – all LEDs;
HIGH – Main Beam LED in its high (brightest) setting;
LOW – Main Beam LED in its low (dimmest) setting; or
HALO – 8 Area LED lights.
CAUTION: DO NOT OPERATE WHILE CHARGING.
Disconnect the charging cable or adapter, then select the light mode as follows:
To turn the spotlight on and use
Press the trigger once.
the Main Beam LED and 8 area lights
at once
To use the Main Beam LED alone in its
Press the trigger a second time within 5
brightest setting
seconds.
To use the Main Beam LED alone in its
Press the trigger a third time within 5
dimmer setting
seconds.
To switch the spotlight to HALO
Press the trigger a fourth time within 5
mode, using just the 8 area LED lights
seconds.
To turn the spotlight off
Either press the trigger a fifth time within
5 seconds OR press the trigger once after
5 seconds in any mode.
Notes:
The battery/charge status LED indicator will light in one of three colors (as
described in the "Reading the Battery/Charge Status LED Indicator" section) to
indicate the battery status.
If the light's battery voltage is nearly low, the unit will switch automatically to
Halo mode even if another Light Mode has been selected.
Using the Swing-up Stand
Lift the Swing-up Stand up, invert the unit and set it upon a flat, stable surface for
hands-free operation.
OPERATING THE 12 VOLT DC/USB CHARGING ADAPTER'S USB
POWER PORT
The 12V DC/USB charging adapter can be used to power and/or recharge USB-power
electronic devices. Plug the 12V DC/USB charging adapter into a vehicle's 12 volt DC
accessory outlet or other functioning 12 volt DC power source. The LED indicator on the
12V DC/USB charging adapter will light green to indicate that it is properly connected.
Then simply plug the USB device into the USB outlet and operate normally.
Note:
Some vehicles require that the ignition be switched to the accessory outlet
position in order to power the accessory outlet
OPERATING THE 120 VOLT AC/USB CHARGING ADAPTER'S
USB PORT
Plug the 120 volt AC/USB charging adapter into a (powered) standard North American
120 volt 60Hz outlet. Then simply plug the USB device into the USB outlet and operate
normally.
CARE AND MAINTENANCE
All batteries lose energy from self-discharge over time and more rapidly at higher
temperatures. When the unit is not in use, we recommend that the battery is charged at
least every 3 to 6 months.
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces
of the spotlight unit with a soft cloth moistened with a mild solution of water and
detergent.
Except for the fuse in the 12 volt DC/USB charging adapter, there are no user-replaceable
parts. Periodically inspect the condition of adapters, connectors and wires. Contact
manufacturer to replace any components that have become worn or broken.
Battery replacement/disposal
BATTERY REPLACEMENT
The battery should last the service life of the unit. Service life is dependent on a number
of factors including but not limited to the number of recharge cycles, and proper
care and maintenance of the battery by the end user. Contact manufacturer for any
information you may need.
SAFE BATTERY DISPOSAL
Contains a lithium-ion battery, which must be disposed of
properly. Recycling is required. Failure to comply with local,
state and federal regulations can result in fines, or imprisonment.
Please recycle.
WARNINGS:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical
tape to prevent shorting (shorting can result in injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
Replacing the Fuse in the 12V DC/USB Charging Adapter
2. Remove center contact and fuse.
CENTER CONTACT
3. Check fuse with a continuity checker.
2A FUSE
4. If blown, locate a replacement 2 amp
fuse.
END CAP
5. Replace the fuse, center contact and
end cap.
6. Screw end cap clockwise until it is
finger tight - DO NOT OVER-TIGHTEN.
7. Test for proper operation of the 12 volt
DC/USB charging adapter.
1. Unscrew the end cap counterclockwise
and remove.
TROUBLESHOOTING
The spotlight will not charge
• Check that the spotlight is turned off.
• Check that the USB charging cable is properly connected to either the 12V DC/USB
charging adapter or the 120V AC/USB charging adapter, and to the spotlight.
• Check the connection to the AC or DC power source. Make sure there is good contact.
• Confirm that there is functioning AC or DC current.
• Check the plug fuse in the 12V DC/USB charging adapter. Replace the fuse following
the instructions in this manual, if necessary.
• The unit may have shut down to protect the battery from overheating after a long
period of operation or charging. Unplug the charging adapter from the power source
and disconnect the USB charging cable from the spotlight. Allow the spotlight to cool
down for a period before resuming charging.
The spotlight will not operate
• Make sure the 5-Position On/Off Trigger has been pressed to turn the spotlight on.
• The internal battery may be completely discharged. Charge the unit following the
directions given in this manual.
• The unit may have shut down to protect the battery from overheating after a long
period of operation or charging; or the ambient temperature has dropped below
-20°C. Allow the spotlight to cool down or warm up for a period before resuming
operation.
• If the ambient temperature is too hot or too cold the spotlight will not operate.
The 12V DC/USB charging adapter's USB port will not operate / LED indicator on
the 12V DC/USB charging adapter does not come on
• Check the connection to the 12 volt DC power source. Make sure there is good contact.
• Confirm there is functioning DC current.
• Check the plug fuse in the 12V DC/USB charging adapter. Replace the fuse following
the instructions in this manual, if necessary.
• Make sure the rating of equipment plugged into the charging adapter's USB port does
not exceed 2.1A continuous.
• Some household USB-powered electronics will not operate with this USB port. Check
the manual of the corresponding electronic device to confirm that it can be used with
this type of USB port.
The 120V AC/USB charging adapter's USB port will not operate
• Make sure you have live AC power to the outlet the 120V AC/USB charging adapter is
plugged into.
• Make sure the rating of equipment plugged into the charging adapter's USB port does
not exceed 1A continuous.
• Some household USB-powered electronics will not operate with this USB port. Check
the manual of the corresponding electronic device to confirm that it can be used with
this type of USB port.
If the unit does not charge or operate after taking the steps given above, contact the
manufacturer at (877) 571-2391.
ACCESSORIES
Recommended accessories for use with your tool may be available from the
manufacturer. If you need assistance regarding accessories, please contact the
manufacturer at (877) 571-2391.
WARNING: The use of any accessory not recommended for use with this appliance
could be hazardous.
SERVICE INFORMATION
Whether you need technical advice, repair, or genuine factory replacement parts, contact
the manufacturer at (877) 571-2391.
ONE-YEAR LIMITED WARRANTY
The manufacturer warrants this product against defects in materials and workmanship
for a period of ONE (1) YEAR from the date of retail purchase by the original end-user
purchaser ("Warranty Period").
If there is a defect and a valid claim is received within the Warranty Period, the defective
product can be replaced or repaired in the following ways: (1) Return the product to the
manufacturer for repair or replacement at manufacturer's option. Proof of purchase may
be required by manufacturer. (2) Return the product to the retailer where product was
purchased for an exchange (provided that the store is a participating retailer). Returns
to retailer should be made within the time period of the retailer's return policy for
exchanges only (usually 30 to 90 days after the sale). Proof of purchase may be required.
Please check with the retailer for their specific return policy regarding returns that are
beyond the time set for exchanges.
This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting
from normal wear and tear, accidents; damages sustained during shipping; alterations;
unauthorized use or repair; neglect, misuse, abuse; and failure to follow instructions for
care and maintenance for the product.
This warranty gives you, the original retail purchaser, specific legal rights and you may
have other rights which vary from state to state or province to province. This product is
not intended for commercial use.
Please complete the Product Registration Card and return within 30 days from purchase
of the product to: Baccus Global LLC, One City Centre, 1 North Federal Highway, Suite
200, Boca Raton, FL 33432. Baccus Global LLC, toll-free number: (877) 571-2391.
SPECIFICATIONS
Light (Conforms to UL STD. 73)
Bulb:
Main LED bulb and 8 white LEDs
Battery:
Lithium-Ion, 3.6 V DC
Input:
5V DC, 1A (120 Volt AC/USB Charging Adapter) or
2.1A (12 Volt DC/USB Charging Adapter)
12V DC/USB Charging Adapter (Conforms to UL STD. 2089) (Optional Accessory)
Input:
12V DC, 1.1A
Output:
5V DC, 2.1A
Fuse:
2A
120V AC/USB Charging Adapter (Conforms to UL STD. 62368-1)
(Optional Accessory)
Input:
120V AC, 60Hz, 6.7W
Output:
5V DC, 1A
To purchase optional accessories, contact the manufacturer at (877) 571-2391
Imported by Baccus Global LLC, One City Centre, 1 North Federal Highway, Suite 200,
Boca Raton, FL 33432 www.Baccusglobal.com 1-877-571-2391
RD072617
7/26/2017 11:10:22 PM
.

Advertisement

loading

Summary of Contents for Stanley SL5HS

  • Page 1 Plug the 120 volt AC/USB charging adapter into a (powered) standard North American maintenance or modification of tools or equipment could result in serious injury and Congratulations on purchasing your new Stanley 2M Lithium-Ion LED Spotlight. 120 volt 60Hz outlet. Then simply plug the USB device into the USB outlet and operate property damage.
  • Page 2 Por favor completar la tarjeta de registro del producto dentro de un plazo de 30 días Levantar el soporte plegable, invertir la unidad y colóquela sobre una superficie que es Felicitaciones por adquirir su nuevo Stanley 2M linterna LED de litio-ion. Lea el utilizarlo.