Key Refrigerator Dimensions; Assemble The Enclosure For The Refrigerator; Install The Lower And Upper Vents - Norcold N621 Installation Manual

Key Refrigerator Dimensions

These key refrigerator dimensions are for your reference as
necessary (See Art01733).
Refrigerator cabinet width w/o trim - 23.1in. ....................... 1
Refrigerator width overall w/ trim - 24.6 in. ......................... 2
Refrigerator cabinet to side trim - 0.80 in. .......................... 3
Refrigerator cabinet height w/o trim ................................... 4
N600 models - 52.6 in.
N800 models - 59.6 in.
Refrigerator height overall w/ trim ....................................... 5
N600 models - 54.5 in.
N800 models - 61.5 in.
Refrigerator cabinet to top/bottom trim - 0.93 in. ................ 6
Enclosure wall to hinges - 1.10 in. ..................................... 7
Refrigerator cabinet to center of handles ............................ 8
N600 models - 32.5 in.
N800 models - 39.5 in.

Assemble the Enclosure for the Refrigerator

1. Make sure the enclosure is 59.88 - 60.01 inches high for
N82X, N82XXX, N84X, N84XXX, N84XIM, and N84XIMXX
models or 52.88 - 53.01 inches high for N62X, N62XXX,
N64X, N64XXX, N64XIM, and N64XIMXX models x 23.50 -
23.63 inches wide x 24.00 inches deep.
2. Make sure the floor is solid and level.
- The floor must be metal or a wood panel and extend the full
width and depth of the enclosure.
- The floor must be able to support the weight of the refrigera-
tor and its contents.
3. Make sure there are no adjacent heat sources such as a
furnace vent, a hot water heater vent, etc.
Installation Manual 4

Install the Lower and Upper Vents

1. Using the following chart, decide which vents and rough
opening (RO) sizes to use:
Certified Vent P/N
Upper Roof 622293
Exhaust Cap
Upper Roof 616319
Exhaust Vent
Upper Exhaust 621156
& Lower Intake
Plastic
Lower Square 616010
Corner Intake
2. Install the lower intake vent (See Art01598, Art01599, and
Art01602):
NOTE: The lower intake vent is also the service access
opening for the components on the rear of the refrig-
erator.
WARNING:
Make sure the bottom of the opening of the
lower intake vent is even with or immediately below the
floor level. This allows any leaking propane gas to
escape to the outside and not to collect at floor level.
- Make sure the bottom of the opening of the lower intake vent
[1] is even with or immediately below the floor level.
- Align the lower intake vent vertically below the coils [2] and
the condenser [3] of the refrigerator.
3. Install the upper exhaust vent:
CAUTION:
Make sure that no sawdust, insulation, or
other construction debris is on the refrigerator or in the
enclosure. Debris can cause a combustion hazard and
prevent the refrigerator from operating correctly.
NOTE: Tighten the screws of the upper roof exhaust cap to 10
inch-pounds max. Also make sure that the air flow
around the upper roof exhaust cap is not blocked or
decreased by other roof mounted features such as a
luggage carrier, an air conditioner, a solar panel, etc.
- If the design of the vehicle allows, install the roof exhaust
vent [4] directly above the condenser [3] of the refrigerator
(See Art01598):
- Install a baffle [5] to prevent stagnant hot air in the area
[6] above the refrigerator.
RO Height RO Width
N/A N/A
24 in. 5 1/4 in.
13 3/4 in. 21 1/2 in.
9 3/4 in. 19 3/8 in.