Norcold N1095 Installation Manual page 5

- Put one baffle between the top rear edge of the
refrigerator and the inside edge of the upper
exhaust vent opening.
- Put the other baffle between the outside edge of
the upper exhaust vent opening and the side wall
of the vehicle.
- If the depth of the enclosure is 24 inches or more and is
less than 25 inches, no baffles are necessary at the rear of
the enclosure.
- If the depth of the enclosure is 25 inches or more and is
less than 26 inches, add two baffles [10] to the rear of the
enclosure (See Art01676 and Art01677).
- Put one baffle 18 inches to 18 1/2 inches above the
bottom of the enclosure [26] (4 1/4 inches to 4 3/4
inches above the top of the lower intake vent opening
REF) [27] .
- Put the other baffle at the lowest edge of the condenser
[3] of the refrigerator.
- Make sure that the baffles are 1 inch or less [28]
from the coils [2] and condenser [3] of the refrig-
erator.
- Make sure that the baffles are the full width of the
inside of the enclosure.
- If the depth of the enclosure is more than 26 inches, install
a wood or an aluminum or galvanized sheet solid box baffle
[25] in the rear of the enclosure (See Art01681 and
Art01682).
- Make sure that the bottom of the solid box baffle is 18
inches to 18 1/2 inches above the bottom of the
enclosure [26] (4 1/4 inches to 4 3/4 inches above the
top of the lower intake vent opening REF) [27] .
- Make sure that the back of the solid box baffle is
perpendicular to the bottom of the enclosure.
- Make sure that the back of the solid box baffle is either
against the top of the enclosure or against the angled
baffle [8] (depending on the vehicle design).
- Make sure that the solid box baffle is one inch or
less [28] from the coils [2] and condenser [3] of the
refrigerator.
- Make sure that the solid box baffle is the full width
of the inside of the enclosure.
- If there is more than 1/2 inch of clearance between either
side of the refrigerator and the wall, fill the space with
fiberglass insulation or add a baffle to eliminate the excess
clearance.
- If the design of the vehicle does not allow you to install a
roof exhaust vent, install an upper side-wall exhaust vent.
NOTE: The refrigerator is 23.7 in. min. to 24.0 in. max. from
the rear of the breaker to the rear of the condenser
[11] and 55.7 in. min. to 56.0 in. max. from the bottom
of the refrigerator to the bottom of the refrigerator
condenser [12] (See Art01678).
- Install the upper side-wall exhaust vent [13] (See
Art01679 and Art01680).
- Make sure the distance [14] from the bottom of the
enclosure to the top of the rough opening for the
upper exhaust vent is at least 62 inches.
- Align the upper exhaust vent [13] horizontally above
the lower intake vent [1] of the refrigerator.
- To prevent stagnant hot air in the area above the
refrigerator, install an aluminum or galvanized
steel sheet baffle [15] between the top of the
refrigerator and the top of the upper exhaust vent.
- Make sure there is less than 1/4 inch clear-
ance between the baffle and the top of the
refrigerator [16] and that the baffle overlaps
the refrigerator 1 inch or less.
- Make sure that the baffle is against the wall of
the vehicle at the top of the upper exhaust vent
and 1/4 inch or less from the top of the
opening for the upper exhaust vent [17].
- Make sure the baffle is the full width of the
inside of the enclosure
- Make sure the clearance at the sides of the refrigerator is
correct:
- If there is more than 1/2 inch of clearance between
either side of the refrigerator and the wall, fill the space
with fiberglass insulation or add a baffle to eliminate
the excess clearance.
- When using an upper side-wall exhaust vent:
- If the depth of the enclosure is more than 24 inches
and less than 26 inches [18], install a bent aluminum
or galvanized steel sheet baffle [19] to the rear of the
enclosure (See Art01679).
- Make sure that the bend of the baffle is the full
width of the inside of the enclosure.
- Make sure that the bend of the baffle is flush with
the bottom edge of the upper intake vent door
frame.
Installation Manual 5