Table of Contents
Advertisement
2.2 Controller's display
The LCD screen on the controller changes according to current conditions. This section
describes the status display, operating display, FUNC menu, and main menu screens.
2.2.1
Status display
1
2
3
4
5
6
7
8
9
10
1.
Occupied mark. Indicates another controller
has the access rights.
2.
Indicates the ship's MMSI.
3.
Indicates the ship's position and that time.
4.
Indicates the communication mode and
channel.
5.
Indicates the receiver is scanning.
6.
Indicates the Tx power condition (reduction
settings) as follows.
High
Low
7.
Indicates the following conditions if Tx
frequency is not tuned.
Not tuned
Tuning
Tuned
8.
Indicates transmission status (PA power).
9.
When in reception or standby, indicates
strength of received signal (S meter), or
when in transmission, indicates strength of
transmitted signal (TX meter) in one of the
pre-set units shown below.
Tx power (PWR)
Antenna current (Ia)
PA voltage (Vc)
PA current (Ic)
Key information (KEY)
Note: When transmitting in ARQ mode, KEY
is displayed regardless of the above
mentioned setting.
Additionally, the right icon indicates the
built-in loud speaker is on or off. The mark
of
indicates the squelch is on.
The frequency display of the controller in this manual is described as setting
Note
status of seven digit display. (See 5.3.8 for frequency display setting.)
I D 4 3 1 0 0 1 2 3 4
P o s 8 9 ﾟ 5 9 . 0 1 2 3 ' N
1 7 9 ﾟ 5 9 . 6 7 8 9 ' E @ 2 3 : 5 9
TEL ITU- 401
4357.00
RX
L
T
4065.00
TX
ON
S I G
W K R s c a n b a n d s :
2 4 6 8 1 2 1 6 M H z
10. Indicates the frequency (band) the DSC
11. Indicates the equipment is running on DC
12. Indicates current time as follows:
13. Indicates the source of the ship's position
: (Blank)
:
14. Indicates the quality of the ship's position
: Blinks
: Lights
: (Blank)
15. Indicates the user channel in use is
16. Indicates channel or frequency is duplex
17. Indicates the reception frequency.
18. Indicates the transmission frequency. TX
19. Indicates the reception status (attenuation,
20. Indicates the operation guidance (shortcut)
2 3 : 5 9 ( U T C )
G
S
PS
TD
*
D
UP
kHz
kHz
12 -S N2
N o n D S T :
+
M
1
ENU
D R O B O S :
+
M
2
ENU
E d t D S T :
+
M
3
ENU
watch keeping receiver is monitoring for
distress and safety calls.
power.
Universal time coordinated : UTC
Local time
information.
* For details, see 9.3 (3) in this document.
information.
* For details, see 9.3 (3) in this document.
transmitted at the band power level
because the channel power is not
registered.
for communicating with a coast station.
mark is highlighted when transmitting.
AGC, noise reduction).
to send the DSC messages.
NonDST: To send a non-distress call,
holding down the MENU, press
DROBOS: To send a drobose call,
holding down the MENU, press
EdtDST: To edit & send a distress call,
holding down the MENU, press
Names and Functions
11
12
13
14
15
16
17
18
19
20
: LT
1
key.
2
key.
3
key.
2-3
Advertisement
Table of Contents
