Table of Contents
Advertisement
Service Modes, Error Codes, and Fault Finding
–
Skipping, blanking of "Not favourite", "Skipped" or
"Locked" presets/channels.
–
Automatic storing of Personal Preset or Last Status
settings.
–
Automatic user menu time-out (menu switches
back/OFF automatically.
–
Auto Volume levelling (AVL).
How to Activate SDM
To activate SDM, use the following methods:
•
Press the following key sequence on the RC transmitter:
"062596", directly followed by the "Home" button.
After activating this mode, "SDM" will appear in the upper left
corner of the screen.
On Screen Menu
After activating SDM, the following items are displayed, with
SDM in the upper right corner of the screen to indicate that the
television is in Service Default Mode. Menu items and
explanation:
•
xxxxx Operating hours (in decimal).
•
AAAAB-X.YYY See
Software Identification, Version, and
Cluster
for the software name definition.
•
ERR Shows all errors detected since the last time the
buffer was erased in format <xxx> <xxx> <xxx> <xxx>
<xxx> (five errors possible).
•
OP Used to read-out the option bytes. In this chassis two
times eight option codes are used.
How to Navigate
As this mode is read only, there is nothing to navigate. To
switch to other modes, use one of the following methods:
•
Command MENU from the user remote will exit SDM.
•
To prevent the OSD from interfering with measurements in
SDM, use the command "Adjust" or "Options" ("STATUS"
or "INFO" for NAFTA and LATAM) from the user remote.
This will switch the OSD "off" while remaining in the SDM
mode. The "SDM" OSD is remains visible in the upper right
corner of the screen. To exit SDM switch to "Stand-by"
mode.
•
Press the following key sequence on the remote control
transmitter: "062596" directly followed by the OK button to
Table 5-1 SAM mode overview
Main Menu
Sub-menu 1
System Information
Op Hour
Main SW ID
ERR
OP1
OP2
Clear
Press [OK] to clean the Error Codes
immediately
RGB Align
Warm
Normal
Cool
Store
NVM editor
Address
Value
Store
Upload to USB
Copy Channel List to USB
Copy NVM to USB
Copy Readable Info to USB
Copy EDID to USB
switch to SAM (do not allow the display to time out between
entries while keying the sequence). Remarks: new remote
controls will not have I+ button, but an "INFO" button
instead.
How to Exit SDM
•
Switch the set to Stand-by by pressing the standby button
on the remote control transmitter or on the television set.
•
Via a standard customer RC-transmitter: key
in "00"-sequence.
Note: If the TV is switched "off" by a power interrupt while
in SDM, the TV will show up in the last status of SDM menu
as soon as the power is supplied again. The error buffer will
not be cleared.
5.2.3
Service Alignment Mode (SAM)(option)
Purpose
•
To modify the NVM.
•
To display/clear the error code buffer.
•
To perform alignments.
Specifications
•
Operation hours counter (maximum five digits displayed).
•
Software version, error codes, and option settings display.
•
Error buffer clearing.
•
Option settings.
•
Software alignments (White Tone).
•
NVM Editor.
•
Set screen mode to full screen (all content is visible).
How to Activate SAM
To activate SAM, use one of the following methods:
•
Press the following key sequence on the remote control
transmitter: "062596", directly followed by the "INFO"
button. Do not allow the display to time out between entries
while keying the sequence.
•
Or via ComPair.
After entering SAM, the following items are displayed,
with "SAM" in the upper right corner of the screen to indicate
that the television is in Service Alignment Mode.
Sub-menu 2
00183
e.g. "T911E 1.164E" or "T911HE 1.178A"
e.g. "000 000 000 000 000"
e.g. "012 007 208 002 056 032 007 030"
e.g. "056 023 000 106 064 000 000 122"
R Gain
G Gain
B Gain
R Gain
G Gain
B Gain
R Gain
G Gain
B Gain
back to
div. table
TPS10.1A LA
Description
This represents the life timer. The timer counts normal operation hours,
but does not count Stand-by hours.
See paragraph
Software Identification, Version, and Cluster
software name definition.
Shows all errors detected since the last time the buffer was erased. Five
errors possible.
Used to read-out the option bytes. See paragraph
in the Alignments section for a detailed description. Ten codes are
possible.
Erases the contents of the error buffer. Select this menu item and press
the MENU RIGHT key on the remote control. The content of the error
buffer is cleared.
To align the White Tone. See
paragraph
6.3 Software Alignments
in the Alignments section for a
detailed description
Store the RGB value
Select and fill the NVM address
Select and fill the NVM value
Store the value in the address
To upload several settings from the TV to an USB stick
5.
EN 15
for the
6.4 Option Settings
2013-Jul-05
Advertisement
Table of Contents
