Page 1
Installation and service must be performed by an additional information consult an authorized authorized installer or service agency. installer or service agency. Tested by: IMPORTANT: SAVE THESE INSTRUCTIONS 4001609 FPI FIREPLACE PRODUCTS INTERNATIONAL, LTD. 6988 Venture St., Delta, BC, Canada V4G 1H4 920-551a 10.21.22...
Page 2
Congratulations! You are the owner of a state-of-the-art Pellet Stove. Thank you for purchasing a FPI FIREPLACE PRODUCT. The pride of workmanship that goes into each of our products will give you years of trouble-free enjoyment. Should you have any questions about your product that are not covered in this manual, please contact the GREENFIRE DEALER in your area.
TABLE OF CONTENTS SAFETY LABEL MAINTENANCE Routine Cleaning & Maintenance ......10 Tools required to clean the unit ......10 Copy of Decal ............4 Opening the Door ..........10 Decal Location ............4 Burn Pot & Liner ..........10 Door Glass Cleaning ...........10 INSTALLATION Ash Pan & Door Gaskets ........10 Ash Pan .............11 Safety Warnings &...
SAFETY LABEL On the GF55-2 the safety label is located on the underside of the hopper lid. GF55-2 DECAL LOCATION Locate the rating plate on the GF55 by lifting up the hopper lid. The rating plate will be located on the underside of the hopper lid.
ELECTRICAL: The use of a surge protected power bar is highly SINCE FPI HAS NO CONTROL OVER THE INSTALLATION OF recommended. The unit must be grounded. The grounded electrical YOUR STOVE, FPI GRANTS NO WARRANTY IMPLIED OR STATED cord should be connected to a standard 115 volts (4.6 Amps), 60 hertz...
This may require an adjustment to the slider damper setting or to the auger feed trim setting on low. Since FPI has no control over the quality of pellets that you use, we assume no liability for negative results in selection of wood pellets.
OPERATING INSTRUCTIONS CONTROL BOARD FUNCTIONS 1. AUGER LIGHT: This green light will flash in conjunction with the auger pulse. 2. MODE LIGHT: Responsible for signaling the state of the control board. When the light is flashing the stove is in an automatic start mode or the thermostat AUGER has control of the unit.
OPERATING INSTRUCTIONS OPERATING YOUR PELLET STOVE PRE-BURN INSTRUCTIONS: The burn pot liner holes must be clear and the liner installed properly against the ignitor tube for proper operation. Check the hopper for enough pellets to start the unit. Note: The thermostat mode can be changed during normal operation. DO NOT OPERATE THE UNIT WITH THE DOOR OR ASH PAN OPEN.
OPERATING INSTRUCTIONS SLIDER / DAMPER SET-UP THE SLIDER / DAMPER MUST BE SET AT TIME OF INSTALLATION. A Qualified Service Technician or Installer must set the Slider Damper. This is used to regulate the airflow through the pellet stove. The slider damper knob is located on the left cab side (see Figure 7). Figure 8: Efficient Flame.
MAINTENANCE ROUTINE CLEANING & MAINTENANCE The following list of components should be inspected and maintained If after long periods of burning, the fire continually builds up and overflows routinely to ensure that the appliance is operating at its optimum and the burn pot or there is a build up of clinkers, this is an indication that giving you excellent heat value: the pellet fuel quality is poor or the stove may need cleaning.
MAINTENANCE ASH PAN FRESH AIR INTAKE (weekly) (season) The ash pan is located under the burner. Always dispose of the ashes into Inspect periodically to be sure that the intake pipe is not clogged with a metal container (never use cardboard, plastic or wood containers) stored any foreign materials.
MAINTENANCE EXHAUST PASSAGES POST SEASON CLEAN-UP (season) Once you are finished using the pellet appliance for the season, unplug the stove for added electrical protection. It is very important that the stove Removal of the firebox backing for bi-annual cleaning (refer to be cleaned and serviced as stated above.
Warranty protects against defect in manufacture or FPI factory assembled components only, unless herein specified otherwise. Any part(s) found to be defective during the warranty period as outlined above will be repaired or replaced at FPI’s option through an accredited distributor, dealer or pre-approved and assigned agent provided that the defective part is returned to the distributor, dealer or agent for inspection if requested by FPI.
Page 15
Minor movement, expansion and contraction of the steel is normal and is not covered under the terms of this warranty. FPI is not liable for the removal or replacement of facings or finishing in order to repair or replace any appliance in the field.
Page 16
Customers should contact the authorized selling dealer to obtain warranty service. In the event the authorized selling dealer is unable to provide warranty service, please contact FPI by mail at the address listed below. Please include a brief description of the problem and your address, email and telephone contact information. A representative will contact you to make arrangements for an inspection and/or warranty service.
Page 17
Phone: Email: For purchases made in CANADA: For purchases made in the UNITED STATES: For purchases made in AUSTRALIA: FPI Fireplace Products Fireplace Products US, Inc. Fireplace Products Australia Pty Ltd 99 Colemans Road International Ltd. PO Box 2189 PMB 125 Dandenong South, Vic.